Publicidad
Safety
Signs, symbols and instructions placed on this product must never be covered or removed and must
remain present and clearly legible throughout the entire lifetime of the product. Immediately replace or
repair illegible or damaged signs, symbols and instructions. Contact your local dealer for instructions.
In case an adverse event occurred in relation to the device, incidents should be reported to your local
dealer and the national competent authority in a timely manner. The local dealer will forward the
information to the manufacturer.
Caregiver
• Read the "User Manual" carefully before use
and keep it for future reference. Incorrect
use of this product may cause serious injury
to the user.
• Always use the correct lifting techniques and
aids for this purpose.
• Never leave the user unattended in this
product. Ensure permanent supervision by
a caregiver.
• Repairs/replacements must only be made
using new original R82 spare parts and
fittings and carried out in accordance
with the guidelines and service intervals
prescribed by the supplier.
• Settings and adjustments to the product or
accessories are only to be made by persons
who have read the user manual.
• Before the user is allowed to operate the
remote control, the user's cognitive state
must be assessed and considered to be
sufficient to operate it.
• There is a risk of loss of balance for the user
when using the tilt function. The seat must
only be tilted in a controlled manner.
• If there is any doubt as to the continued
safe use of your R82 product or if any
parts should fail, stop using the product
immediately and contact your local dealer
as soon as possible.
• Transportation of the product whilst the user
is in it is not allowed. It is allowed to use the
product with the user safely strapped in it
for transfers over short distances. Do not
cross any obstacles during transfer.
• Ensure that moving parts do not squeeze or
trap body parts when adjusting them.
• Ensure that body parts are not trapped
in openings for mounting of supports/
accessories.
• Do not let children and youngsters play with
the handset.
• It is important to remove the transport
plastic bag before using the handset. Cables
must be placed in such a way that users or
carers cannot trip and injure themselves.
• Be aware of any MAX mark indications
before adjustment.
• Use this product on a level surface without
any obstacles. Be aware of reduced
maneuverability on slippery surfaces.
etac.com
EN
• When using on inclines, please refer to the
page with measurements.
• Observe the surface temperature on the
product, before placing an user in it. This
goes especially for users with insensitive
skin as they cannot feel heat or cold. If the
surface temperature is above 41°C then
allow the product to cool before use.
• Do not expose the gas spring to pressure or
high temperatures. DO NOT puncture.
• Only use the power unit within specified
working limits.
• Do not expose the piston rod to scratches
etc. - when adjusting the gas spring, it is
important to place a cloth between the tool
used and the piston rod.
• Ensure that the castors/wheels are fully
functional and secure before use.
• Activate the brakes before placing the user
into the product.
• Inspect the product and all of its accessories
and replace any worn out parts before use.
• Ensure the stability of the product before
placing the user in it.
• Carry out all positional adjustments on the
product and accessories and ensure that
all knobs, screws and buckles are securely
fastened before use. Keep all tools out of
the reach of children.
User
• The height and tilt functions can be
operated by the user under the caregiver's
permanent supervision.
Product
• The power unit does not have a safety stop.
• Do not attempt to repair any part of the
power unit.
• The foot support does not have a weight
bearing function and must only be used for
support.
• When the foot support is close to the floor
and the castors, the castors may be unable
to swivel.
• This product is tested for resistance to
ignition at level non-ignition in accordance
with EN 1021-1, EN 1021-2 and ISO 7176-
16.
• The product might lose its resistance to
ignition if non-original R82 parts are used.
• This product must not be occupied in a
motor vehicle. The user must be positioned
47
Publicidad
