Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Switch the hob back on via ON/OFF (1).
The Pause || (10) key flashes for 6 seconds.
Touch the Pause || (10) key.
The recall function becomes active (a beep sounds). All previously
set power levels, timers and fast heat-up are retrieved.
Stand-Alone Timer function
The Stand-Alone Timer function is a countdown independent of the
cooking zones that emits an acoustic signal (beep) when it expires.
The Timer is activated by pressing the central display (5); the two
keys + / - (6) will appear for adjustment.
The Timer can be set when the Display shows "–--".
Set the desired duration of the timer via the + / - keys (6) and it will
be shown in the Display (5).
The timer starts 6 seconds after activating this function (when no
other control is pressed).
The stand-alone timer can be up to 600 minutes. The remaining
time will be displayed in the Zone/Display (5); a beep will sound
at the end of the countdown.
If the remaining time of the timer is less than 1 minute, it will be
displayed in the format shown below and the dot will have a steady
light:
minutes
remaining seconds
There are two ways to switch off the Timer:
• Select
(5) and set the duration of the Timer to
+ / - (6) or
• Press the ON/OFF key (1) twice
• The extraction timer stops the extraction and can only be set
separately when the cooking zones are at zero (when the timer
is started and then the hob is switched off, this time has priority
over the after-fan function).
Cooking Zone Timer
The Cooking Zone Timer function is a countdown (maximum 119
minutes per zone) that can be set, even simultaneously, on each
cooking zone.
At the end of the set time, the cooking zones switch off automatically
and a beep is emitted.
To activate the function:
• Touch the Selection/Display area (2) (with a power level other
than 0).
• Touch the key
(3) corresponding to the cooking zone.
• The display will show "---" and the Timer can be set (with the +
and - keys which will be displayed).
• Use the + / - keys (6) to set the duration of the timer, which is
displayed in the Display area (5). The symbol
during programming.
The cooking zone timer starts after 6 seconds after activation (when
no other key is pressed). To reset the cooking zone timer, press and
hold the key
(3) again.
If desired, Timer programming can be repeated for multiple cooking
zones.
Each cooking zone can have a different Timer set and the display
(5) will show the countdown of the cooking zone selected at that
moment
(3) (flashing) or the timer with the shortest time.
If no zone is selected, press on the Display (5) to view the Stand-
Alone Timer countdown.
22
The countdown display is the same as for the Stand-Alone Timer
(see previous paragraph).
When the timer has finished the countdown, a beep sounds and the
cooking zone switches off.
To deactivate the Timer:
• Select the cooking zone (2) then touch the key
the Timer duration to
Bridge function
This function allows both cooking zones to work simultaneously,
forming a single cooking zone with the same power level.
This function allows even cooking with large pots.
The front "Primary" cooking zone can be used in combination with
the corresponding rear "Secondary" zone.
The function is available on all cooking zones:
2FL (primary) + 2RL (secondary)
2FR (primary) + 2RR (secondary)
Bridge function activation:
• Select a cooking zone and set it to a value greater than 1, then
• Select the two cooking zones you want to use at the same time.
• The "Secondary" cooking zone Display (2) will show the symbol
"
".
• Use the Selection bar (4) to set the operating Level (Power),
which will be shown on the "Main" cooking zone Display (2).
using
Deactivate the Bridge Function:
Select the 2 cooking zones at the same time.
IMPORTANT
During the Bridge Function, the cooking zones are considered a
single cooking area and therefore, if the Timer is active.
Cooking Zones, when this expires both cooking zones to switch off
automatically.
(3) flashes
(3) and set
using the keys + / - (6)
Publicidad
