WIKA A-10 Manual De Instrucciones página 6

7. Starting, operation
Assembly of DIN EN 17501-80 L-connector
(D) Mounting hole
1. Using the head of a small screwdriver in
the mounting hole (D), lever the terminal
block (6) out of the angle housing (5).
In order not to damage the sealing of the
angle housing, do not try to push the
terminal block (6) out using the screw
hole (1) or the cable gland (2).
2. Ensure that the conductor outer diameter
you select is matched to the angle housing's cable gland. Slide the cable through the cable
gland nut (2), washer (3), gland seal (4) and angle housing (5).
3. Connect the flying leads to the screw terminals on the terminal block (6) in accordance
with the pin-assignment drawing.
4. Press the terminal block (6) back into the angle housing (5).
5. Tighten the cable gland (2) around the cable. Make sure that the sealing isn't damaged
and that the cable gland and seals are assembled correctly in order to ensure ingress
protection.
6. Place the flat, square gasket over the connection pins on the top of the instrument
housing.
7. Slide the terminal block (6) onto the connection pins.
8. Secure the angle housing (5) and terminal block (6) to the instrument with the screw (1).
10 WIKA Operating instructions/Betriebsanleitung/Mode d'emploi/Instrucciones de servicio
GB
(1)
(2)
(3)
(5)
(4)
Female
connector
(6)
Sealing
Male connector,
Case with
pressure connection
A-10
7. Starting, operation
Specifications Model A-10
Pressure ranges bar
Over pressure safety bar
Burst pressure bar
Pressure ranges bar
Over pressure safety bar
Burst pressure bar
MPa and kg/cm
{Absolute pressure: 0 ... 1 bar up to 0 ... 25 bar}
Pressure ranges psi
Over pressure safety psi
Burst pressure psi
Pressure ranges psi
Over pressure safety psi
Burst pressure psi
{Absolute pressure: 0 ... 15 psi up to 0 ... 300 psi}
Vacuum resistance
Fatigue life
Materials
 Wetted parts
» Pressure connection
» Pressure sensor
Internal transmission fluid

Case

Power supply U UB in VDC
B
Signal output and RA in Ohm
maximum ohmic load R
A
WIKA Operating instructions/Betriebsanleitung/Mode d'emploi/Instrucciones de servicio
1 1.6 2.5 4 6 10
2 3.2 5 8 12 20
5 10 10 17 34 34
40 60 100 160 250 400
80 120 200 320 500 800
400 550 800 1000 1200 1700
2
are available
15 25 30 50 100 160
30 60 60 100 200 290
75 150 150 250 500 500
500 1000 1500 2000 3000 5000
1000 1740 2900 4000 6000 10000
2500 7975 11600 14500 17400 24650
As of 0 ... 10 bar
10 Mio. cycles
316 L
316 L (as of 0 ... 10 bar rel 13-8 PH)
Silicone oil (only with pressure ranges up to 0 ... 6 bar and
0 ... 25 bar abs)
316 L
8 ... 30 (14 ... 30 with signal output 0 ... 10 V)
RA ≤ (UB – 8 V) / 0.02 A
4 ... 20 mA, 2-wire
0 ... 10 V, 3-wire RA > 10 k
GB
16 25
32 50
100 100
600
1200
2400
200 300
400 600
1500 1500
10000
17400
34800
11
A-10