Power Supply (Fig. E-1) - Tunturi C50 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 59
English
hand pulse sensors. If the skin is too dry or too moist, the pulse rate
measurement will become less accurate.
‼ NOTE
Do not use the hand pulse sensors in combination with a heart
rate chest belt.
If you set a heart rate limit for your workout, an alarm will sound
when it is exceeded.
Heart rate measurement (heart rate chest belt)
‼ NOTE
A chest strap does not come standard with this trainer. When you
like to use a wireless chest strap you need to purchase this as an
accessory.
The most accurate heart rate measurement is achieved with a heart
rate chest belt. The heart rate is measured by a heart rate receiver
in combination with a heart rate transmitter belt. Accurate heart
measurement requires that the electrodes on the transmitter belt are
slight moist and constantly touching the skin. If the electrodes are too
dry or too moist, the heart rate measurement will become less accurate.
⚠ WARNING
If you have a pacemaker, consult a physician before using a
heartrate chest belt.
⚠ CAUTION
If there are several heart rate measurement devices next to each
other, make sure that the distance between them is at least 1.5
metres.
If there is only one heart rate receiver and several heart rate
transmitters, make sure that only one person with a transmitter is
within transmission range.
‼ NOTE
Do not use a heart rate chest belt in combination with the
handpulse sensors.
Always wear the heart rate chest belt under your clothes directly in
contact with your skin. Do not wear the heart rate chest belt above
your clothes. If you wear the heart rate chest belt above your
clothes, there will be no signal.
If you set a heart rate limit for your workout, an alarm will sound
when it is exceeded.
The transmitter transmits the heart rate to the console up to a
distance of 1 metre. If the electrodes are not moist, the heart rate
will not appear on the display.
Some fibers in clothes (e.g. polyester, polyamide) create static
electricity which can prevent accurate heart rate measurement.
Mobile phones, televisions and other electrical appliances create
an electromagnetic field which can prevent accurate heart rate
measurement.
Maximum heart rate (during training)
The maximum heart rate is the highest heart rate a person can safely
achieve through exercise stress. The following formula is used to
calculate the average maximum heart rate: 220 - AGE. The maximum
heart rate varies from person to person.
⚠ WARNING
Make sure that you do not exceed your maximum heart rate
during your workout. If you belong to a risk group, consult a
physician.
Beginner 50-60% of maximum heart rate
Suitable for beginners, weight-watchers, convalescents and persons
who have not exercised for a long time. Exercise at least three times a
week, 30 minutes at a time.
Advanced 60-70% of maximum heart rate
Suitable for persons who want to improve and maintain fitness. Exercise
at least three times a week, 30 minutes at a time.
Expert 70-80% of maximum heart rate
Suitable for the fittest of persons who are used to long-endurance
workouts.
Use
Adjusting the support feet
The equipment is equipped with 4 support feet. If the equipment is not
stable, the support feet can be adjusted.
- Turn the support feet as required to put the equipment in a stable
position.
- Tighten the locknuts to lock the support feet.
‼ NOTE
The machine is the most stable when all support feet are turned
fully in. Therefore start to level the machine by turning all support
feet fully in, before turning out the required support feet to stable
the machine.
Adjusting the pedal position
The both pedals can be adjusted according to the height and the
exercise position of the user.
- Loosen the 2 pedal fixing knobs.
- Move the pedal to the required position.
- Tighten the pedal fixing knobs.
‼ NOTE
Make sure the both pedals are fitted into similar positions always.
Adjusting the console
The console can be adjusted according to the height and the exercise
position of the user.
- Loosen the console adjustment knob.
- Move the console to the required position.
- Tighten the console adjustment knob.

Power supply (Fig. E-1)

The trainer is powered by an external power supply. Refer to the
illustration to locate the trainer's power input.
‼ NOTE
Connect the power supply with the trainer before connecting it to
the wall outlet.
Always remove power cord when machine is not in use.
2 0

Publicidad

Tabla de contenido
loading

Tabla de contenido