Electrical Safety; Description (Fig. A); Exercise Instructions - Tunturi C80 Manual Del Usuario

English

Electrical safety

(Only for equipment with electric power)
- Before use, always check that the mains voltage is the same as the
voltage on the rating plate of the equipment.
- Do not use an extension cable.
- Keep the mains cable away from heat, oil and sharp edges.
- Do not alter or modify the mains cable or the mains plug.
- Do not use the equipment if the mains cable or the mains plug
is damaged or defective. If the mains cable or the mains plug is
damaged or defective, contact your dealer.
- Always fully unwind the mains cable.
- Do not run the mains cable underneath the equipment. Do not run
the mains cable underneath a carpet. Do not place any objects on
the mains cable.
- Make sure that the mains cable does not hang over the edge of a
table.
- Make sure that the mains cable cannot be caught accidentally or
tripped over.
- Do not leave the equipment unattended when the mains plug is
inserted into the wall socket.
- Do not pull the mains cable to remove the mains plug from the wall
socket.
- Remove the mains plug from the wall socket when the equipment
is not in use, before assembly or disassembly and before cleaning
and maintenance.
Assembly instructions

Description (fig. A)

Your Crosstrainer is a piece of stationary fitness equipment used to
simulate cycling without causing excessive pressure to the joints.
Package contents (fig. B & C)
- The package contains the parts as shown in
fig. B.
- The package contains the fasteners as shown in fig. C. Refer to the
section "Description"
‼ NOTE
• If a part is missing, contact your dealer.
Assembly (fig. D)
⚠ WARNING
• Assemble the equipment in the given order.
• Carry and move the equipment with at least two persons.
⚠ CAUTION
• Place the equipment on a firm, level surface.
• Place the equipment on a protective base to prevent damage to
the floor surface.
• Allow at least 100 cm of clearance around the equipment.
• Refer to the illustrations for the correct assembly of the
equipment.
‼ NOTE
• Save the tools provided with this product, after you completed
the product assembly,
for future service purposes.
Fasten Nuts and Bolts
⚠ CAUTION
• Do not over tighten any component with pivoting function.
• Make sure all pivoting components are able to move freely.
DO NOT FASTEN BOLTS
AND NUTS IN THIS STEP
Workouts
The workout must be suitably light, but of long duration. Aerobic
exercise is based on improving the body's maximum oxygen uptake,
which in turn improves endurance and fitness. You should perspire,
but you should not get out of breath during the workout.
To reach and maintain a basic fitness level, exercise at least three
times a week, 30 minutes at a time. Increase the number of exercise
sessions to improve your fitness level.
It is worthwhile to combine regular exercise with a healthy diet. A
person committed to dieting should exercise daily, at first 30 minutes
or less at a time, gradually increasing the daily workout time to one
hour. Start your workout at low speed and low resistance to prevent
the cardiovascular system from being subjected to excessive strain.
As the fitness level improves, speed and resistance can be increased
gradually. The efficiency of your exercise can be measured by
monitoring your heart rate and your pulse rate.

Exercise Instructions

Using your fitness trainer will provide you with several benefits, it will
improve your physical fitness, tone muscle and in conjunction with a
calorie controlled diet help you lose weight.
The warming up phase
This stage helps get the blood flowing around the body and the
muscles working properly. It will also reduce the risk of cramp and
muscle injury. It is advisable to do a few stretching exercises as shown
below. Each stretch should be held for approximately 30 seconds, do
not force or jerk your muscles into a stretch - if it hurts, STOP
The exercise phase
This is the stage where you put the effort in. After regular use, the
muscles in your legs will become more flexible. Work to your but it is
very important to maintain a steady tempo throughout. The rate of
work should be sufficient to raise your heart beat into the target zone
shown on the graph below.
2 0
Securely tighten all Nuts and Bolts after
all components have been assembled in
current and previous steps.
Do not tighten all Nuts and Bolts in this
step.