Pioneer PDP-42MVE1 Manual De Instrucciones página 31

SCREEN
The position of the image can be adjusted and flickering
of the image can be corrected.
Example: Adjusting the vertical position
On "VIDEO WALL" menu, select "SCREEN", then press
the MENU/SET button.
The "SCREEN" screen appears.
On "V.POSITION" of "SCREEN" menu, adjust the position.
SCREEN
SCREEN SIZE :
V.POSITION
H.POSITION
V.SIZE
H.SIZE
AUTO PICTURE :
PHASE
CLOCK
SEL. ADJ. EXIT RETURN
Information
SCREEN settings
These are the same functions as the SCREEN menu on
page 16.
P. ON DELAY (Power on delay)
Use this function to activate power-on delay.
Turn on the AUTO ID before the following operations.
Example: Setting "ON"
On "P. ON DELAY" of "VIDEO WALL" menu, select "ON".
DIVIDER
POSITION
DISP. MODE
AUTO ID
SCREEN
P. ON DELAY
ABL LINK
REPEAT TIMER
SEL.
Information
P. ON DELAY settings
ON: Turns on the main power of each display after a
delay time.
OFF: Turns on the main power of all displays at the
same time.
(Only for 16 and 25 screens)
MODE1: Turns on the main power of each display
delayed.
MODE2: Turns on the main power of each display more
delayed.
* Once this function has been set to "ON", the POWER
ON/OFF button on the remote control does not function
except for the No.1 monitor.
By pressing the POWER ON button on the remote
control the No.1 monitor will turn on and the others
will be turned on one by one automatically.
* From the second monitor onward, neither the POWER
button on the unit nor the POWER ON button on the
remote control works. However, by pressing and holding
the POWER ON button for more than 3 seconds, the
monitor will be turned on.
26
En
4 : 3
OFF
V.POSITION
VIDEO WALL
: 1
: NORMAL
: OFF
: ON
: OFF
: OFF
ADJ. EXIT RETURN
ABL LINK
Use this function to set a uniform brightness for each
display.
Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9)
before the following operations.
Example: Setting "ON"
On "ABL LINK" of "VIDEO WALL" menu, select "ON",
then press the MENU/SET button.
DIVIDER
POSITION
DISP. MODE
AUTO ID
SCREEN
P. ON DELAY
+64
ABL LINK
REPEAT TIMER
SEL.
Information
ABL LINK settings
ON: Sets a uniform brightness for each screen in a video
wall. This can be set only when a 2×2 or 3×3 video
wall is selected.
OFF: Sets the individual screen brightness for each
screen in a video wall.
* When this function is set "ON", connect your plasma
displays with the remote cable (optional) in the order of
the position numbers for the 2×2 video wall. See the
drawing below.
* If there are changes in the DIVIDER or POSITION,
the ABL LINK will automatically turn OFF.
No.1 No.2
REMOTE
IN No.4 No.3
Display 1
No.1 No.2
REMOTE
OUT
No.4 No.3
Display 4
* With the 3×3 video wall, connect the final display to the
first display the same way as with 2×2 video wall.
Note: The remote control can be operated unless the IR
REMOTE is set to "OFF".
VIDEO WALL
: 1
: NORMAL
: OFF
: OFF
: ON
: OFF
ADJ. EXIT RETURN
REMOTE
OUT
No.1 No.2
REMOTE
No.4 No.3 OUT
REMOTE
IN
Display 2
REMOTE
OUT
No.1 No.2
REMOTE
No.4 No.3
IN
REMOTE
IN
Display 3