Ninja WOODFIRE Pro Connect XL Instrucciones página 29

COOKING FUNCTIONS
IMPORTANT: Review all warnings at the beginning of this Instruction Booklet before proceeding.
Smoker
PRESET: 120°C 4 hours
TEMP RANGE: 60-210°C
TIME RANGE: 10 mins-12 hours
1
Place grill on a flat, level surface.
2
Open the lid and install the grill plate by
positioning it flat on top of the heating
element so it sits in place.
NOTE: If you are using the probe, refer to the
Using the Built-In Probe(s) section.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 Pull the smoker box open and use the pellet
scoop to fill the smoker box with Ninja
Woodfire Pellets to the top. DO NOT overflow
smoker box.
5 Open the lid and place ingredients on the grill
plate. Close the lid.
6 Make sure the grill is plugged in and press
the MODE button or use the dial to select the
SMOKER function.
NOTE: Ninja Woodfire Flavour is automatically
enabled when using the Smoker function.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
after 5 seconds.
9 Press START to begin cooking. There is no
preheat time for the Smoker function. The
pellets will go through an ignition cycle (IGN)
for 3-6 minutes, then the grill will begin
cooking and the timer will begin to count
down.
10 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
11 Remove food from the grill plate.
56 ninjakitchen.eu
Grill
PRESET: Medium 25 mins
TEMP RANGE: Low-High
TIME RANGE: 1 min-1 hour
1 Place grill on a flat, level surface.
2 Open the lid and install the grill plate by
positioning it flat on top of the heating
element so it sits in place.
NOTE: If you are using the probe, refer to the
Using the Built-In Probe(s) section.
3 Install the grease tray by sliding it into place at
the back of the grill.
4 If you plan to add Ninja Woodfire Flavour,
pull the smoker box open and use the
pellet scoop to fill the smoker box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoker box.
5 Make sure the grill is plugged in and press the
MODE button or use the dial to select the
GRILL function.
6
If adding Ninja Woodfire Flavour, press the
WOODFIRE FLAVOUR button.
7 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
8 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
inafter 5 seconds.
9 Press START to begin preheating. If using
Ninja Woodfire Flavour, the pellets will go
through an ignition cycle (IGN), then the grill
will begin preheating (PRE).
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the lid and place
ingredients on the grill plate. Once the lid
is closed, cooking will begin and the timer
will start counting down. Skip to step 12.
10 When preheating is complete, the grill will
beep and ADD FOOD will appear on the display.
11 Open the lid and place ingredients on the grill
plate. Once the lid is closed, cooking will begin
and the timer will begin counting down.
NOTE: Want to cook with the lid open?
After you've added food, keep the lid open, the
timer will begin to count down after 30 seconds,
and you will be cooking with bottom heat only.
12 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
13 Remove food from the grill plate.
IMPORTANT: Review all warnings at the beginning of this Instruction Booklet before proceeding.
Air Fry
PRESET: 200°C 12 mins
TEMP RANGE: 150-240°C
TIME RANGE: 1min-1 hour
1 Place grill on a flat, level surface.
2 Open the lid and install the grill plate by
positioning it flat on top of the heating
element so it sits in place.
3 Place the crisper basket on the grill plate,
positioning the basket feet in the designated
indentations.
NOTE: If you are using the probe, refer to the
Using the Built-in Probe section.
4 Install the grease tray by sliding it into place at
the back of the grill.
5
If you plan to add Ninja Woodfire Flavour,
pull the smoker box open and use the pellet
scoop to fill the smoker box with Ninja
Woodfire Pellets to the top.
DO NOT overflow the smoker box.
6 Make sure the grill is plugged in and press the
MODE button or use the dial to select the AIR
FRY function.
7
If adding Ninja Woodfire Flavour, press the
WOODFIRE FLAVOUR button.
8 The default temperature setting will display.
To adjust temperature, if desired, press TEMP
and use the dial to increase or decrease
temperature. Press dial to confirm, otherwise
temperature will lock in after 5 seconds.
9 To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
10 Press START to begin preheating. If using
Ninja Woodfire Flavour, the pellets will go
through an ignition cycle (IGN), then the grill
will begin preheating (PRE).
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the lid and place
ingredients in the crisper basket. Once the lid
is closed, cooking will begin and the timer will
start counting down. Skip to step 13.
11 When preheating is complete, the grill will beep
and ADD FOOD will appear on the display.
12 Open the lid and place ingredients on the grill
plate. Once the lid is closed, cooking will begin
and the timer will begin counting down.
13 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
14 Remove food from the crisper basket.
Roast
PRESET: 180°C 1 hour 30 mins
TEMP RANGE: 120-220°C
TIME RANGE: 1min-4 hours
1 Place grill on a flat, level surface.
2
Open the lid and install grill plate by
positioning it flat on top of the heating
element so it sits in place.
NOTE: If you are using the probe, refer to the
Using the built-in Probe section.
3 Install the grease tray by sliding it into place
at the back of the grill.
4 If you plan to add Ninja Woodfire Flavour,
pull the smoker box open and use the
pellet scoop to fill the smoker box with
Ninja Woodfire Pellets to the top. DO NOT
overflow the smoker box.
5
Make sure the grill is plugged in and press the
MODE button or use the dial to select the
ROAST function.
6 If adding Ninja Woodfire Flavour, press the
WOODFIRE FLAVOUR button.
7 The default temperature setting will
display. To adjust temperature, if desired,
press TEMP and use the dial to increase or
decrease temperature. Press dial to confirm,
otherwise temperature will lock after 5
seconds.
8
To adjust cook time, press TIME and use the
dial to increase or decrease cook time. Press
dial to confirm, otherwise cook time will lock
in after 5 seconds.
9 Press START to begin preheating. If using
Ninja Woodfire Flavour, the pellets will go
through an ignition cycle (IGN), then the grill
will begin preheating (PRE).
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing and holding the START/STOP
button for 4 seconds. ADD FOOD will flash
across the screen. Open the lid and place
ingredients in the crisper basket. Once the lid
is closed, cooking will begin and the timer will
start counting down. Skip to step 12.
10 When preheating is complete, the grill will
beep and ADD FOOD will appear on the
display.
11 Open the lid and place ingredients on the
grill plate. Once the lid is closed, cooking will
begin and the timer will begin counting down.
12 When cook time reaches zero, the grill will
beep and DONE will appear on the display.
13 Remove food from grill plate.
ninjakitchen.eu 57