Publicidad
Idiomas disponibles
Idiomas disponibles
i) Never stand upon the table saw and never use the table saw
as a foot stool. Serious injuries could occur if the power tool falls
over or if you accidentally come into contact with the saw blade.
j) Ensure the saw blade is always mounted in the correct
direction of rotation. Do not use sanding discs or wire
brushes with the table saw. Improper assembly of the saw
blade or the use of not recommended accessories can lead to
serious injuries.
General view:
1. Saw blade protection
2. Splitting cotter
3. Saw blade
4. Angle stop
5. Sliding door
6. Holes for attachment
7. Adjusting scale
8. Longitudinal stop
9. On/off switch
10. Pipe union for vacuum cleaner
11. 3 mm hexagon key
12. 2 mm hexagon key
Description of the machine
The KS 230 cuts wood and similar materials up to 8 mm, plastics
up to 3 mm and non-ferrous metals up to 1.5 mm. The basic
equipment includes a saw blade, a longitudinal stop, an angle
stop, two fixing bolts, a rubber adapter for vacuum cleaner con-
nection as well as two hexagon keys.
We recommend original PROXXON replacement saw blades.
Technical data:
Generated noise
Eff. acceleration
Weight
Dimensions
Bearing surface
Max. cutting thickness
Max. saw blade Ø
Saw blade drill hole:
Motor
Rotational speed
Voltage
Power rating
Noise/vibration information
The information on vibration and noise emission has been deter-
mined in compliance with the prescribed standardised and norma-
tive measuring methods and can be used to compare electrical
devices and tools with each other.
These values also allow a preliminary evaluation of the loads
caused by vibration and noise emissions.
80dB(A)
2
2.5 m/s
1.8 kg
160x160 mm
12 mm
58 mm
10 mm
8,000/min
230 Volt 50/60Hz
85 wat
Depending on the operating conditions while operating the device,
the actually occurring emissions could differ from the values spec-
ified above!
Please bear in mind that the vibration and noise emission can devi-
ate from the values given in these instructions, depending on the
conditions of use of the tool. This is especially applicable in depen-
dence on the work piece to be machined and the utilised saw blade
and its wear condition. Always ensure you have an adequately sharp
saw blade and a well-maintained drive. Poorly maintained tools,
inappropriate working methods, different work pieces, too high a
feed or unsuitable work pieces or materials or unsuitable bits and
cutters (here: saw blade) can significantly increase the vibration load
and noise emission across the entire work period.
To more accurately estimate the actual vibration and noise load, also
take the times into consideration where the device is switched off,
or is running but is not actually in use. This can clearly reduce the
vibration and noise load across the entire work period.
• To reduce vibrations, make sure your tool and the cutting disc or
the saw blade are in proper condition!
• Ensure regular and proper maintenance of your tool
• Stop operation of the tool immediately if excessive vibration
occurs!
• Unsuitable bits and cutters (here e.g. cutting disc or saw blade)
can cause excessive vibration and noises. Only use suitable bits
and cutters!
• Take breaks if necessary when working with the device!
Please note that the sound and vibration measurements in particu-
lar have been performed with Proxxon bits and cutters. When using
third-party brands we cannot guarantee compliance with the state-
ments given here!
Protective insulation safety class system 2
For your safety, always wear hearing protection
while working!
Use only indoors
Risk of injury!
Never work without dust protection mask and safety
glasses. Some dusts have a hazardous effect! Mate-
rials containing asbestos may not be machined!
Please do not dispose off the machine!
Operation
Before start-up
Mounting the machine
The MICRO-circular saw must be fastened onto a sturdy wooden
board using the enclosed fixing bolts 1 (Fig.2) The board can then
be fixed onto a sturdy table using two fastening clamps.
Warning!
Warning:
- 11 -
Publicidad
