Kärcher KIRA CV 50 Manual Del Usuario página 19

LED light colour
Red
Modes
Cleaning modes
There are two cleaning modes to choose from. In both
modes, the cleaning robot systematically cleans the
room by dividing it into segments. A cleaning around the
edges of the segment is always carried out first. The
cleaning robot then cleans the segment "lanes".
Basic Modus:
● One-time cleaning that cannot be scheduled.
● Suitable for closed rooms in which the cleaning ro-
bot is allowed to move freely.
● The cleaning robot can be operated via the app
without any set-up and is ready for use immediately
after the initial start-up.
● The cleaning robot does not need to be set up in ad-
vance. Cleaning is carried out without a previously
established and stored map.
● After cleaning, the cleaning robot returns to the
starting point where it began cleaning.
Routine mode:
● Suitable for complex environments that require reg-
ular cleaning. To be able to use this mode, a map of
the surroundings must be created beforehand. The
card is named in the app and should be processed
for efficient cleaning.
● To carry out cleaning, an already created map is se-
lected on the cleaning robot. This allows the clean-
ing robot to plan the segments efficiently from the
beginning and to work in an even more productive
manner. The map adapted by the user is taken into
account by the cleaning robot when planning the
segments.
● The cleaning of a selected map can be started by
using the display on the cleaning robot or through a
scheduled cleaning in the app.
● The cleaning robot must be placed in the starting ar-
ea (approx. 2 m x 2 m) of the map.
● If the map selected on the cleaning robot does not
match the outline of the room to be cleaned where
the cleaning robot is located, the localisation fails
and the cleaning robot does not start cleaning. A no-
tification appears on the display.
Suction strength
The desired suction strength can be selected on the
cleaning robot's display under "Settings" > "Suction
mode" or in the app. The setting applies to the entire
map, except for special cleaning zones.
1 Normal mode
2 Eco mode
● Reduced suction performance and brush speed
● Energy-saving: resulting in longer run time
● Reduced volume: thus suitable for noise-sensi-
tive environments, e.g. in corridors in front of con-
ference rooms or hotel rooms
Sleep mode
The cleaning robot automatically switches to sleep
mode after 5 minutes of inactivity.
The display is switched off, the cloud or app connection
and the buttons remain active.
To exit sleep mode, press any operation button.
Meaning
● Critical fault
● Alarm
● Cleaning cannot be carried out
● Human assistance required
When light and sound are activated, the cleaning robot
emits an acoustic signal and visual signal as soon as an
error occurs.
Critical error (red):
● The cleaning robot cannot continue cleaning.
● The cleaning robot emits an acoustic signal and the
LED strip flashes red
● A notification is displayed in the app.
Warning notice (orange):
● The cleaning robot emits an acoustic signal and the
LED strip flashes orange.
● Cleaning continues. Human assistance may be nec-
essary,e.g. to change the battery packs or empty the
dirt receptacle. Once the cleaning robot finishes
cleaning or a battery change is necessary before-
hand, the robot returns to the starting point of the
map.
● A notification is displayed in the app.
1. Check the package contents when unpacking.
2. In case of shipping damage, inform dealer immedi-
ately.
3. Remove the protective film from the top of the de-
vice, the battery compartment cover and the lid of
the storage compartment for the telescopic handle.
4. Remove the foam to protect the safety bumper.
Charging battery packs
Charge the battery packs (see operating instructions
and safety instructions for the battery packs and the
charger).
Note
Fully charge the battery packs each time they are
charged before reinserting them into the device.
Installing the side brush
1. Push the side brushes into the holders at the bottom
of the device until they audibly click into place.
Note
Two screws are included to secure the side brushes to
the device if they should come loose during cleaning
and require additional securing.
English
Error mode
Unpacking
Startup
19