Kärcher KIRA CV 50 Manual Del Usuario página 25

1. Clean the wheel running surfaces.
Emptying the dust container
1. Press the unlocking button on the dust container
and remove the dust container from the device.
2. If necessary, lift up the handle on the dust container.
3. Press the unlocking button on the door of the dust
container.
4. Lower the door of the dust container.
5. Empty the dust container.
Cleaning the filter
1. Press the unlocking button on the dust container
and remove the dust container from the device.
2. Press the tab on the filter cover and lift up the filter
cover.
3. Remove the filter.
4. Knock out the filter.
Removing and cleaning the cleaning brush
1. Remove the cover of the cleaning brush with sweep-
ing edge.
Malfunctions without information shown on the display
Malfunction
The cleaning robot can-
not be switched on
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.
Warranty
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing flaw is the cause. In a warranty case, please con-
tact your dealer (with the purchase receipt) or the next
authorised customer service site.
(See overleaf for the address)
Further warranty information (if available) can be found
in the service area of your local Kärcher website under
"Downloads".
Declaration of Conformity
EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Autonomous vacuum cleaner
Type: 1.454-500.0
Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2014/53/EU
2011/65/EU
Harmonised standards used
EN 60335-1
EN 60335-2-72
EN 62368-1: 2014
EN 62311: 2020
EN IEC 63000: 2018
EN IEC 55014-1: 2021
Rectification
1. Check whether the battery packs are charged and charge them if necessary.
2. Remove the cleaning brush.
3. Remove tangled threads and hairs.
Removing and cleaning the side brush
1. Remove the side brush from the holder.
2. Remove tangled threads and hairs.
Cleaning the sensors
1. Clean the sensors with a moist, lint-free cloth. If nec-
essary, use additional glass cleaner.
Troubleshooting guide
If an error occurs, a notification appears on the device
display with instructions that must be followed to correct
the problem.
For error messages that can only be rectified by a ser-
vice technician, an error code is also displayed. If this
still occurs after several restarts, please contact cus-
tomer service.
EN IEC 55014-2: 2021
EN 301 489-1 V2.2.3
EN 301 489-17 V3.2.4
EN 301 489-52 V1.2.1
EN 301 908-1 V15.1.1
EN 301 908-2 V13.1.1
EN 301 908-13 V13.2.1
EN 301 511 V12.5.1
EN 300 328 V2.2.2
EN 301 893 V2.1.1
Additional implemented standard
IEC63327:2021
EN 60335-2-69
The signatories act on behalf of and with the authority of
the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2024/11/01
Declaration of Conformity (UK)
We hereby declare that the product described below
complies with the relevant provisions of the following
UK Regulations, both in its basic design and construc-
tion as well as in the version put into circulation by us.
This declaration shall cease to be valid if the product is
modified without our prior approval.
Product: Autonomous vacuum cleaner
Type: 1.454-500.0
English 25