Publicidad
Idiomas disponibles
Idiomas disponibles
INTERNET SPEED TEST
Press the O K button in order to test the Internet speed.
ADVANCED SETTINGS
Press the O K button to call up further network configura-
tion options.
– CONFIGURATION
Choose the setting AUTOMATIC IP or MAN
UAL IP. If you select MANUAL IP, three addi-
tional lines appear in which you can manually
enter the data for the IP ADRESS, SUBNET
MASK and DEFAULT GATEWAY using the di-
rection buttons and the number buttons.
– CONFIGURATION
Select here between AUTOMATIC DNS or
MANUAL DNS. If you select MANUAL DNS,
two additional lines appear in which you can
manually enter the data for the DNS SERVER
and DNS SERVER using the direction but-
tons and the number buttons.
An existing network connection can be termi-
nated by pressing the red button.
NETWORKED STANDBY MODE
Activate/deactivate the Wake-On LAN/Wake-On Wireless
LAN function (WoL/WoWLAN). This enables you to switch
on the smart TV via a different device. Both devices must
be connected to the same network via LAN or Wi-Fi for
this purpose. Select the ON setting to activate this func-
tion. The device being used as a remote control needs to
be connected to the TV once when it is switched on. The
control function only works when the TV is in standby
mode.
Exit the network settings by pressing O K .
6.7.2. Devices
1
2
3
Audio Link
Input Device
Here you can pair audio devices via Bluetooth and input
devices such as a mouse or keyboard with the unit.
AUDIO LINK: Connect audio devices via Bluetooth.
Press to switch the function on or off.
INPUT DEVICE: Connect input devices via Bluetooth.
Press to switch the function on or off.
4
5
6
Devices
Lorem ipsum
Enabled
Disabled
Next
OK
BACK
EXIT
HOME
6.7.3. Receptiom method
1
2
3
Select Broadcast Type:
Scan Encrypted Channels
Select favourite network type
D. Aerial
D. Cable
Satellite
Analogue
Before the station search starts, select the following op-
tions:
SCAN ENCRYPTED CHANNELS: Use to select
whether encrypted channels should also be searched
for.
SELECT FAVOURITE NETWORK TYPE: Use to
select the preferred reception method. If you use sev-
eral types of reception, you can select the types below
with and activate with O K .
Select NEXT with and confirm with O K .
6.7.4. Cable digital
If you have previously activated the reception type DIG
ITAL CABLE, you can now make settings for the network
search. If it should be necessary, you can adjust the
NETWORK, FREQUENCY, the NETWORK ID and the
SEARCH STEP correspondingly.
6.7.5. Satellite
If you have previously activated the reception type SAT
ELLITE, you can now make settings for the antenna type.
To set the antenna type, select one of the following
antenna types:
– DIRECT: Select this antenna type if you have a sin-
gle receiver and a satellite antenna. Press the OK
button and then choose the desired satellite (you
can also call up the transponder list using the blue
button). Afterwards, press the O K button again to
start the search. After that, decide whether or not
the channel list should be loaded.
– UNICABLE: Select this antenna type if you have
multiple receivers and a single-cable system. Press
the O K button and make all the necessary set-
tings regarding SATELLITE POSITION /, USER
BAND and BAND FREQUENCY (here you can
also call up the transponder list using the blue
button). Afterwards, press the O K button again to
start the search. After that, decide whether or not
the channel list should be loaded.
– DISEQC SWITCH: Select this antenna type if you
have multiple satellite antennas and a DiSEqC
switch. Press the O K button and activate the de-
sired DISEQC switch (here you can also call up
the corresponding transponder list using the blue
button). Afterwards, press the O K button again to
start the search. After that, decide whether or not
the channel list should be loaded.
4
5
6
On
None
Next
OK
BACK
EXIT
HOME
13
DE
FR
IT
NL
EN
ES
Publicidad
