Operation And Display Elements - Wolf Garten EXPERT 105.220 Instrucciones De Funcionamiento

English
If an empty battery (type 2)
is supplied
(Battery with filler plugs)
Remove the filler plugs of the

battery cells (Fig. 3b).
Fill each cell slowly with battery

acid up to 1 cm below the filling
opening.
Let the lead in the battery absorb

the battery acid for thirty minutes.
Check the level of the battery

acid, add more if necessary.
Before using the battery for

the first time, charge it using
a battery charger (max. charging
current 12 Volt/6 Ampere) for
2 to 6 hours. After charging the
battery, first pull out the battery
charger plug, then disconnect the
battery (see also operating
instructions for the battery
charger).
Re-insert the filler plugs of the

battery cells.
Install the battery in the

appliance.
Remove the strip seal from the

battery vent. Connect the venting
hose so that the free end points
downwards in the appliance.
The hose must always allow free
passage! (Fig. 3c)
First connect the red cable (+),

and then the black cable (–).
Thereafter, use only distilled

water to top up the battery
(check every 2 months).
Keep the battery clean.

Operation and
Display elements
Warning!
Damage to the appliance.
The control and indicator functions
will be described to begin with.
Do not perform any functions at this
stage!
Ignition lock
(depending on model)
Fig. 4
Start: Turn the key to the right
until the engine is running, then
release. Key is on
key anti-clockwise to
Note
If the ignition lock features a light
position , the light is switched on
when the ignition key is moved
back to this position when the
engine has started.
Ignition lock with OCR
function (depending on
model)
Fig. 5
This ignition lock features an OCR
function (= user-controlled mowing
in reverse gear).
Start: Turn the key to the right
until the engine is running, then
release. The key at
(normal) allows mowing in the drive
direction.
OCR position: Turn key to left of
normal position to reverse mowing
position and press the
switch (1). The indicator light (2)
comes on and indicates to the user
that the unit can now mow in
reverse and forward gear.
Stopping: Turn the key to the left,
to .
Note
Do not use the OCR function
unless absolutely necessary,
otherwise work with the key in the
normal position. The OCR function
switches off automatically as soon
as the key is turned to the normal
position or the engine is switched
off (stop position or disconnection
of the engine by the safety interlock
system).
Choke (depending
on model)
Fig. 6
To start a cold engine, pull the
choke (Fig. 6a), or move the
accelerator lever to
Operating instructions for lawn tractors
Throttle
Fig. 7
The engine speed can be adjusted
continuously.
Fast engine speed =
Slow engine speed =
stop: Turn
.
Brake pedal
Fig. 8
The brake pedal can be used
to brake quickly, to engage and
disengage the locking brake,
and to switch OFF speed control.
Direction-of-travel lever
(only for models with
autodrive)
Fig. 9
The direction lever must be used
only when the tractor is stationary.
To do this, fully depress and hold
down the brake pedal.
Forwards = lever to "F/ "
Idle = lever to "N"
Reverse = lever to "R/ "
Lever for setting the cutting
height
Fig. 10
Using the lever (A), set the different
cutting height levels (1 to max. 12 –
depending on model).
Level 1 = Smallest cutting height –
cutter deck all the way down.
Level 12 * = Largest cutting height
– cutter deck all the way up.
(* Depending on model. Highest
number corresponds to the largest
cutting height.)
Note
Depending on the model,
the adjustment link features an
adjustable position indicator (B).
This is used to find the required
cutting height more quickly.
PTO lever
(depending on model)
Fig. 11
The PTO lever actuates a mecha-
nism to switch ON and OFF the
cutters.
Switch off cutter deck
lever out of recess and pull all the
(Fig. 6b).
way backwards.
.
.
= Press
7