Wolf Garten EXPERT 105.220 Instrucciones De Funcionamiento página 12

English
Switch on cutter deck
press lever forwards and engage in
recess.
PTO switch
(depending on model)
Fig. 12
The PTO switch actuates an
mechanical clutch to switch ON
and OFF the cutters.
ON = pull the switch.
OFF = press the switch.
Note: When the safety lock system
has automatically switched OFF
the appliance (e.g. when reversing
with activated cutters), first switch
ON and then OFF the PTO switch
to release the lock on the clutch.
Parking brake/Speed control
Fig. 13
This switch has a dual function on
some models:
Actuate the parking brake
Press down the brake pedal fully,
and press the switch.
Release the parking brake:
Press down the brake pedal fully,
the switch disengages.
Tempomat switch on
(depending on model):
When driving, press the switch.
The forward speed selected at
this point (but not top speed) is
maintained, and the drive pedal
can be released.
When the accelerator pedal or
the brake pedal is depressed,
the cruise control automatically
switches off.
Drive pedal for appliances
with hydrostatic drive
Fig. 14
The drive pedal is used to adjust
the speed continuously and to
change direction:
Forwards = push forwards the drive
pedal (in direction ), the further
forward, the faster.
Stop (for stationary vehicle and
changing direction) = release the
drive pedal (N).
Reverse = push back the drive
pedal (counter to direction
the further back, the faster.
8
Drive pedal for appliances
= Slowly
with auto drive
Fig. 15
The drive pedal is used to adjust
the speed continuously:
– Move the direction-of-travel lever
to "F" (forwards) ( ) or "R"
(reverse) ( ).
– Forwards = push forwards the
drive pedal (in direction), the
further forward, the faster.
Transmission release for
machines with a hydrostatic
drive
Fig. 16
To push the unit when the engine
is switched off.
Depending on model:
Pull out lever and press down

(Fig. 16a). To drive the unit,
push lever up and press in.
or
:
Pull out lever and press up

(Fig. 16b). To drive the unit,
push lever down and press in.
The lever is situated on the rear
panel of the machine.
Display cluster
(depending on model)
Fig. 17
According to the model, the combi-
nation indicator can consist of the
following elements.
Oil pressure (1): The indicator light
is lit while the engine is running,
immediately switch off engine and
check oil level. Where necessary,
visit a garage.
Brake (2): Indicator lamp lights up if
the brake pedal is not depressed or
the parking brake is not locked
when the engine starts.
Cutter deck (PTO) (3): Indicator
lamp lights up if the cutter deck
(PTO) is not switched off when the
engine starts.
Battery charge indicator (4): If the
indicator light lights up when the
engine is running, this means
that the battery is not sufficiently
charged. Where necessary, visit
a garage.
),
Operating instructions for lawn tractors
Operating hours counter (5):
Indicates the completed operating
hours when the ignition is switched
on.
Ampere meter (6):
This shows the charging current
from the generator to the battery.
Optional functions:
– When the ignition is switched on,
the battery voltage indicator is
indicated for a short period and
then the operating hours are
indicated.
The operating hours are always
counted except for when the
ignition key is in the "Stop"
position or when it is removed.
– Each time 50 operating hours
have elapsed (according to the
model), the oil change indicator
"CHG/OIL" appears in the display
for five minutes. This message
appears after the next two hours
of operation. See the engine
manual for oil change intervals.
Seat (depending on model)
Fig. 18
a) Pull the lever, and adjust the
seat.
or
b) Loosen adjusting screw, adjust
seat and retighten adjusting screw.
Level indicator for grass
catcher (depending on
model)
Fig. 19
The level sensor measures how full
the grass catcher attachment is
during mowing. An acoustic signal
is generated when the grass
catcher is full. The grass catcher
must be emptied.
Switch for catch basket
lifting device (depending
on model)
Fig. 20
The switch (A) is used to open and
close the grass catcher (electro-
mechanically). Operation – see
separate "Grass catcher attach-
ment" operating manual.