Metabo HPT C 3607DRA Manual De Instrucciones página 6

English
8. When replacing the saw blade, always confi rm that
the rpm rating of the new blade is correct for use on
this tool.
9. Always shut off the power and wait for the saw
blade to completely stop rotating before doing any
maintenance or adjustments.
10. During slide cutting, always push the saw blade away
from the operator.
11. Always clamp or otherwise secure the workpiece to
the fence; otherwise the workpiece might be thrust
form the table and cause bodily harm.
12. During miter or bevel cutting, always wait for the
rotation of the blade to stop completely before lifting
the saw blade.
13. Always make a trial run fi rst before attempting any
new use of the saw.
14. Always handle the saw blade with care when
dismounting and mounting it.
15. Always confi rm that the workpiece is free of nails or
other foreign objects before beginning a cut.
16. Always keep your hands out of the path of the saw
blade.
17. Always confi rm that the lower guard is in the proper
place before using the saw.
18. Always confi rm that the lower guard does not obstruct
the sliding motion of the saw before attempting slide
cutting.
19. Always confi rm that the motor air vents are fully open
before using the tool.
20. Always wait until the motor has reached full speed
before starting a cut.
21. Always keep the handles dry, clean and free of oil and
grease. Hold the tool fi rmly when in use.
22. Always use outboard stands to provide support for
long workpieces that overhang the table of the slide
compound miter saw.
23. Always operate the tool after ensuring the workpiece
is fi xed properly with a vise assembly.
24. The operating instructions provided with the tool
shall direct the user to secure the tool to supporting
structure if, during normal operation, there is a
tendency for the tool to tip over, slide, or walk on the
supporting surface.
25. Ensure before each cut that the machine is stable.
26. If the saw blade should become jammed, switch the
machine off and hold the workpiece until the saw
blade comes to a complete stop. To prevent kickback,
the workpiece may not be moved until after the
machine has come to a complete stop.
Correct the cause for the jamming of the saw blade
before restarting the machine.
27. Use only saw blades that are marked with a maximum
permitted speed equal or higher than the no-load
speed marked on the POWER TOOL.
6
28. Use only a saw blade diameter in accordance with the
markings on the POWER TOOL.
29. Replace the table insert when worn.
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully
understand the operating instructions contained in
this Manual.
2. Never leave tool running unattended. Turn power off .
Don't leave tool until it comes to a complete stop.
3. Never operate the POWER TOOL when you are
tired, after you have taken any medications, or have
consumed any alcoholic beverages.
4. Never use the POWER TOOL for applications not
specifi ed in the instruction manual.
5. Never operate the tool while wearing loose clothing,
a necktie or jewelry, or while your hair is uncovered,
to protect against getting caught in the moving
machinery.
6. Never reach around the saw blade.
7. Never touch any moving parts, including the blade,
while the saw is in use.
8. Never remove any safety devices or blade guards;
use of the tool without them would be hazardous.
9. Never lock the lower guard; always confi rm that it
slides smoothly before using the tool.
10. Never attempt to move a plugged-in POWER TOOL
while your fi nger is on the starting switch.
11. Never use the POWER TOOL if the starting switch
does not turn on and off properly.
12. Never use the POWER TOOL if the plastic housing or
the handle is cracked or deformed.
13. Never use the POWER TOOL near fl ammable liquids
or gases because sparking can cause an explosion.
14. Never clean plastic components with solvents
because the plastic may dissolve.
15. Never operate the saw unless all the blade guards are
in place.
16. Never raise the saw blade from the workpiece until it
has fi rst come to a complete stop.
17. When slide cutting, never pull the handle toward the
operator, since this could cause the saw blade to kick
up from the workpiece. Always push the handle away
from the operator in a single, smooth motion.
18. Never place your limbs inside of the line next to
warning sign " " while the tool is being operated.
This may cause hazardous conditions.
19. Never use abrasive type blades on this saw.
20. Never expose to rain or use in damp locations.
21. Never cut ferrous metals or masonry.
22. Do not replace the laser with a diff erent type.