Fcc Compliance Statement; Additional Information; Industry Canada Statement - DSC Neo Power Serie Manual De Usuario

A p p e n d i x D : R e g u l a t o r y A p p r o v a l s

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls
could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television
reception, which can be deter-mined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the fol-
lowing measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to
Identify and Resolve Radio/Television Interference Problems". This booklet
is available from the U.S. Government Printing Office, Washington D.C.
20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this
equipment is a label that contains, among other information, the FCC registra-
tion number and ringer equivalence number (REN) for this equipment. If
requested, this number must be provided to the Telephone Company.
HS2128 Product IdentifierUS: F53AL01BHS2128
REN:0.1B
USOC Jack:RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compat-
ible modular jack that is also compliant. See installation instructions for
details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the
devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as deter-
mined by the total RENs, contact the local Telephone Company. For products
approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is sep-
arately shown on the label.
Incidence of Harm
If this equipment HS2016/HS2032/HS2064/HAS2128 causes harm to the
telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice is
not practical, the Telephone Company will notify the customer as soon as pos-
sible. Also, you will be advised of your right to file a complaint with the FCC
if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, oper-
ations or procedures that could affect the operation of the equipment. If this
happens the Telephone Company will provide advance notice in order for you
to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment HS2016/HS2032/HS2064/
HAS21284 for repair or warranty information, please contact the facility indi-
cated below. If the equipment is causing harm to the telephone network, the
Telephone Company may request that you disconnect the equipment until the
problem is solved. This equipment is of a type that is not intended to be
repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122

Additional Information

Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation commis-
sion for information.
Alarm dialling equipment must be able to seize the telephone line and place a
call in an emergency situation. It must be able to do this even if other equip-
ment (telephone, answering system, computer modem, etc.) already has the
telephone line in use. To do so, alarm dialling equipment must be connected
to a properly installed RJ-31X jack that is electrically in series with and ahead
of all other equipment attached to the same telephone line. Proper installation
is depicted in the figure below. If you have any questions concerning these
instructions, you should consult your telephone company or a qualified
installer about installing the RJ-31X jack and alarm dialling equipment for
you.

INDUSTRY CANADA STATEMENT

NOTICE: This Equipment, HS2016/HS2032/HS2064/HAS2128,
meets the applicable Industry Canada Terminal Equipment Technical Specifi-
cations. This is confirmed by the registration number. The abbreviation, IC,
before the registration number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the
equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal equip-
ment is 0.1. The REN assigned to each terminal equipment provides an indi-
cation of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any com-
bination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all devices does not exceed five.
L'indice d'équivalence de la sonnerie
(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être rac-
cordés à une interface téléphonique. La terminaison d'une interface peut con-
sister en une combinaison quelconque de dispositifs, à la seule condition que
la somme d'indices d'équivalence de la sonnerie de tous les dispositifs
n'excède pas 5.
Certification Number:
IC: 160A-HS2128
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
119