Installation; Incoming Inspection; Preparatory Work; Execution - Reflex Servitec 35-95 Manual De Instrucciones Original

6 Ins tallation
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
• Ensure that the system is voltage-free before installing the device.
• Ensure that the system is secured and cannot be reactivated by other
persons.
• Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical engineering
regulations.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there i s a
risk of burns and other injuries at the connection points, if pressurised hot water
or hot steam suddenly escapes.
• Ensure proper installation, removal or maintenance work.
• Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
• Wear protective gloves.
• Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to falls or bumps
Bruising from falls or bumps on system components during installation.
• Wear personal protective equipment (helmet, protective clothing, gloves,
safety boots).
 Note!
Confirm that installation and start-up have been carried out correctly
using the installation, start-up and maintenance certificate. This action
is a prerequisite for the making of warranty claims.
– Have the Reflex Customer Service carry out commissioning and
the annual maintenance.
6.1 I ncoming inspection
Prior to shipping, this device was carefully inspected and packed. Damages
during transport cannot be excluded.
Proceed as follows:
1. Upon receipt of the goods, check the shipment for
• completeness and
• possible transport damage.
2. Document any damage.
3. Contact the forwarding agent to register your complaint.
6.2 P r eparatory work
Condition of the delivered device:
• Check all screw fittings and electrical connections of the Servitec for proper
seating.
Tighten the screws and fittings as necessary.
Pre paring the device installation:
• Frost-free, well-ventilated room.
• Ambient temperature > 0 to maximal 45 °C.
• Level, stable flooring with a drainage facility.
• Filling connection DN 15 to DIN 1988 -100/ -600 / DIN EN 1717.
• Electric connection 230 V~, 50/60 Hz, 16 A with upstream ELCB: Tripping
current 0.03 A.
The Servitec can be operated in two different modes for water make-up. When
installing the Servitec, note its position within the system:
•
•


6.3
ATTENTION
Da mage due to improper installation
Additional device stresses may arise due to the connection of pipes or system
equipment.
•
•
In heating systems, preferably install the device in the return side.
–
–
The device is pre-wired and must be adapted for the local system conditions.
Complete the water-side connection to the system and the electric connection as
shown in the terminal diagram, see chapter 6.5 "Electrical connection" on
page 29 .

6.3.1
Install the "DV" degassing valve (2) with the check valve (1) on the "VT" vacuum
spray tube. Check all screw fittings of the Servitec for proper seating.
6.3.2
The Servitec is installed on the floor. Select the attachment means according to
the floor properties and the weight of the Servitec.
Vacuum spray degassing — 24.04.2020 - Rev. A
Pressure-dependent make-up of system water (Magcontrol).
– Install the Servitec in the vicinity of the expansion vessel.
Level-dependent make-up of system water (Levelcontrol).
– Install the Servitec on the system side in the return upstream of the
return flow admixture.
Note!
Servitec make-up line.
– Use the Fillset system separator if the make-up line of the drinking
water mains is closed.
– The applicable guidelines and regulations of the country of
installation must be observed.
Note!
Comply with the Reflex planning directive.
– During planning, take into account that the working range of the
Servitec must be between the "pa" supply pressure and the "pe"
final pressure in the working range of the pressure maintenance
system.

Execution

Ensure that pipes are connected from the device to the system without
them being stressed or strained.
If necessary, provide support structures for the pipes or equipment.
ATTENTION
Property damage caused by leaks
Leaks in the connection pipes to the device can cause material damage to the
facility system.
• Use only connection pipes with appropriate resistance against the facility
system temperature.
In this manner, you ensure that the device is operated within the
permissible pressure and temperature ranges.
In systems with return admixtures or hydraulic switching points, the device
must be installed upstream of the admixture point to ensure degassing in
the "V" main flow volume at temperatures ≤ 90 °C.
Note!
During installation, pay attention to the operability of the valves and the
inlet options for the connecting lines.
F itting the add-on components
Ins tallation location

Installation

English — 27