Power Stroke PS14120 Manual Del Operador página 18

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

 Engage the lock-out on the trigger handle by pushing the
trigger lock button to the right.
 Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the trigger handle.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high pres-
sure hose prior to and during each use and do not allow
it to become kinked. The high pressure hose features an
outer covering that provides strength to the hose. If the
outer covering becomes damaged, stop using the hose
and replace it immediately. A kinked or damaged hose
can develop a high pressure leak and result in a possible
injection or other serious personal injury.
To prevent damage to the outer covering:
 Inspect the hose before every use.
 Fully unwrap and straighten hose before use.
 Do not allow the high pressure hose to be kinked.
 Keep hose away from hot surfaces and sharp edges.
 Do not pull unit by high pressure hose.
 Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 12 - 13.
As sold, this unit is designed for use with "downstream" pres-
sure washer detergents. To convert for use with "upstream"
detergents, contact an authorized customer service center
for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
To clean:
 Pour detergent in the detergent tank.
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process, make sure the unit is
cleaned and dried before proceeding.
OPERATION
 Install the soap nozzle on the spray wand.
 Start the pressure washer and spray the detergent on
a dry surface using long, even, overlapping strokes. To
prevent streaking, do not allow detergent to dry on the
surface.
To rinse:
 Using the 15˚ nozzle, spray away from the rinsing surface
for approximately 10 seconds to allow any remaining
detergent to be flushed from the line.
 Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 14.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should be
added to the unit after every use and before storage. Pump
protector can be purchased at the retailer where you pur-
chased your pressure washer, or by calling customer service.
The instructions below are for G-Protect Pump Protector.
For other brands, follow the instructions provided by the
manufacturer.
 Turn off the pressure washer motor and shut off the water
supply. Pull trigger to release water pressure.
 Disconnect garden hose and high pressure hose.
 Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
 Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
 Squeeze bottle to inject contents into pump.
 Pump is protected when the protector fluid exits the pump
outlet.
MOVING THE PRESSURE WASHER
See Figure 15.
 Turn the pressure washer off. Point nozzle in a safe direc-
tion and pull trigger to release water pressure.
 Raise the handle up until the handle knob snaps through
the locking hole.
 Tilt the machine slightlly toward you until it balances on
the wheels then roll the machine to the desired position.
 DO NOT attempt to move the unit by pulling on any of
the hoses.
Page 14 — English

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido