Instructions And Safety Information; General Safety - salmson SHS Serie Instalacion Y Puesta En Servicio

English
1.8.4 Maintenance
The prescribed maintenance and inspection work should be
carried out regularly. This work may only be carried out by quali-
fied, trained and authorized personnel. Repairs not listed in this
operation and maintenance manual and all types of repair work
may only be performed by the manufacturer and authorized
service centers.
1.8.5 Damage to the product
Damage as well as malfunctions that endanger safety must be
eliminated immediately by trained personnel. The product
should only be operated if it is in proper working order. During
the agreed warranty period, the product may only be repaired
by the manufacturer or an authorized service workshop! The
manufacturer reserves the right to have the damaged product
delivered by the operator to the factory for inspection!
1.8.6 Exclusion from liability
No liability will be assumed for product damage if one or more
of the following points applies:
- A construction by the manufacturer based on faulty and/or
incorrect information provided by the operator or customer
- Non-compliance with the safety instructions, the regulations
and requirements in terms of German law and/or the applica-
ble local laws, as well as this operating and maintenance
manual
- Improper use
- Incorrect storage and transport
- Improper assembly/dismantling
- Insufficient maintenance
- Unqualified repairs
- Faulty construction site and/or construction work
- Chemical, electrochemical and electrical influences
- Wear
This means the manufacturer's liability excludes all liability for
personal, material or financial injury.
2 SAF E TY
This chapter lists all the generally applicable safety instructions
and technical information. Furthermore, each remaining chap-
ter contains specific safety instructions and technical informa-
tion. All instructions and information must be observed and
followed during the various phases of the product's life cycle
(installation, operation, maintenance, transport etc.)! The opera-
tor is responsible for ensuring that personnel follow these
instructions and guidelines.
2.1

Instructions and safety information

This manual uses instructions and safety information for pre-
venting injury and damage to property. To uniquely identify
these for personnel, the instructions and safety information are
differentiated as follows:
2.1.1 Instructions
An instruction is displayed in "bold". Instructions contain text
that refers to the previous text or particular sections of chap-
ters, or highlights short instructions.
Example:
Note that products stored with drinking water must be
protected from frost!
2.1.2 Safety information
Safety information is slightly indented and displayed in "bold". It
always commences with a signal word.
Information that only refers to material damage is printed in
gray, without safety symbols.
Information that refers to personal injury is printed in black and
is always accompanied by a safety symbol. Danger, prohibition
or instruction symbols are used as safety symbols.
Example:
Danger symbol: General hazard
Danger symbol, for example, electrical current
Prohibition symbol, for example, Keep out!
Instruction symbol, for example, wear protective
clothing
The safety symbols used conform to the generally valid direc-
tives and regulations, such as DIN and ANSI.
Each safety instruction begins with one of the following signal
words:
- Danger
This can result in serious or fatal injuries!
- Warning
Serious injuries can occur!
- Caution
Injuries can occur!
- Caution (Instruction without symbol)
Substantial material damage can occur. Irreparable damage
is possible!
Safety instructions begin with a signal word and description of
the hazard, followed by the hazard source and potential conse-
quences, and end with advice on prevention.
Example:
Beware of rotating parts!
The rotating rotor can crush and sever limbs. Switch
off the product and let the rotor come to a stop.
2.2

General safety

- When installing or removing the product, never work alone in
rooms and shafts. A second person must always be present.
- The product must always be switched off before any work is
performed on it (assembly, dismantling, maintenance, installa-
tion). The product must be disconnected from the electrical
system and secured against being switched on again. All
rotating parts must have come to a stop.
- The operator should inform his/her superior immediately
should any defects or irregularities occur.
- It is of vital importance that the system be shut down immedi-
ately by the operator if any problems arise which may endan-
ger safety of personnel. Problems of this kind include:
- Failure of the safety and/or control devices
- Damage to important parts
- Damage to electric installations, cables, and insulation.
30