Field Settings Table - Rotex RKHBRD011AAV1 Guia De Instalacion

The configuration of pattern B is done by field settings:
1 Select the appropriate pattern: [7-02] = 1
2 Turn on multiple set point 1: [7-03] = 0
Turn on multiple set point 2: [7-04] = 0
3 Enter the temperature multiple set point 1: [A-03] (see below)
Enter the temperature multiple set point 2: [A-04] (see below)
Configuration example:
Set Field
point setting
Space 0 65°C Remote
controller
Space 1 45°C [A-03]
Space 2 35°C [A-04]
Resulting heat pump water
Pattern B can also be used to do some primary multi zoning (if all set
point temperatures are selected the same, no temperature reducing
device ( ) is required).
Multiple thermo ON signals for 3 rooms can be generated. Thermo
OFF signals are only valid if all requests are OFF.

Field settings table

First Second
code code Setting name
0 Remote control setup
00 User permission level
01 Room temperature compensation value
03 Status : space heating schedule timer mode
1 Automatic storage timing for domestic water heating
00 Status: night time storage
01 Night time storage start time
02 Status: day time storage
03 Day time storage start time
2 Automatic setback function
00 Status: setback operation
01 Setback operation start time
02 Setback operation stop time
3 Weather dependent set point
00 Low ambient temperature (Lo_A)
01 High ambient temperature (Hi_A)
02 Set point at low ambient temperature (Lo_Ti)
03 Set point at high ambient temperature (Hi_Ti)
4 Disinfection function
00 Status: disinfection operation
01 Disinfection operation day selection
02 Disinfection operation start time
5 Automatic setback and disinfection set point
00 Set point: disinfection operation temperature
01 Disinfection operation time duration
02 Leaving water setback temperature
03 Room setback temperature
6 Option setup
00 Domestic hot water tank installed
01 Optional room thermostat installed
04 Benefit kWh power supply mode
Installation manual
28
[7-03] = 1
[7-04] = 1
Thermo status
OFF ON OFF OFF OFF
OFF ON/OFF ON ON OFF
OFF ON/OFF OFF ON ON
OFF 65°C 45°C 45°C 35°C
Installer setting at variance with default value
Date
NOTE Leaving water control is not allowed for pattern B.
It is the installers responsibility to make sure no
unwanted situations can occur (e.g. too high
water temperatures towards floor heating loops,
etc.).
It is the installers responsibility to make sure the
water circuit is well balanced (e.g. when a
domestic hot water request occurs, there will be
sufficient flow towards other appliances as well,
etc.)
Rotex does not offer any temperature reducing
device (
possibility to use multiple set points.
When space 0 is in thermo OFF, but space 1 or 2
are active, space 0 will be fed with water at a
temperature equal to the highest set point of
spaces 1 and 2.
This can lead to unwanted heating of space 0.
Value Date Value
). This system only provides the
Default
value Range Step
2 2~3 1
0 –5~5 0.5
1 (ON) 0/1 —
1 (ON) 0/1 —
1:00 0:00~23:00 1:00
0 (OFF) 0/1 —
15:00 0:00~23:00 1:00
1 (ON) 0/1 —
23:00 0:00~23:00 1:00
5:00 0:00~23:00 1:00
–10 –20~5 1
15 10~20 1
70 25~80 1
45 25~80 1
1 (ON) 0/1 —
Fri Mon~Sun —
23:00 0:00~23:00 1:00
70 60~70 5
10 5~60 5
5 0~10 1
18 17~23 1
0 (OFF) 0/1 —
0 (OFF) 0/1 —
0 0/2 1
RKHBRD011~016AAV1+Y1
Indoor unit for air to water heat pump system
4PW55786-1
Unit
—
°C
—
—
hour
—
hour
—
hour
hour
°C
°C
°C
°C
—
—
hour
°C
min
°C
°C
—
—
—