Transport And Storage - salmson HYDROSON M Serie Instalación Y Instrucciones De Puesta En Marcha

ENGLISH
1. GENERAL
1.1 Applications
Pumps for clear liquids in residential, agricultural, and other
applications.
Drawing of water from a well, spring, river, pond, etc. Water should
not be drawn from abyssinian wells (tube, driven well).
1.2 Specifications
• Max. service pressure:
• Temperature range
- Standard version:
• Ambient temperature:
• Suction head:
2. SAFETY
Read this data sheet carefully before installing and starting up. Pay
special attention to the points concerning the safety of the
equipment for the intermediate or end user.
The appliance is not intendend for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsable for their safety. Children should be supervised to
ensure that they do not play with the appliance
2.1 Symbols used in the manual
Calls attention to a potential risk that might affect safety.
Instruction concerning electricity
ATTENTION !
Warning.

3. TRANSPORT AND STORAGE

When taking delivery of the equipment, check that it has not been
damaged in transit. If anything is found wrong, take the necessary
steps with the carrier within the allowed time.
If the equipment delivered is to be installed at a later time,
store it in a dry place and protect it from impacts and
outside hazards (moisture, frost, etc.).
Handle the pump carefully so as not to alter the geometry or
alignment of the hydraulic assembly.
4. PRODUCTS AND ACCESSORIES
4.1. Description (see FIG. 1, 2)
1. : Foot valve-strainer (max. passage cross-section of 1 mm)
2. : Pump suction valve
3. : Pump discharge valve
4. : Check valve
5. : Filling plug
6. : Drain plug
7. : Pipe support
8. : Strainer
9. : Storage tank
10. : Town water supply
11. : Motor protection relay for three-phase motor
SH:
: Suction height
DH: : Discharge height
4.2 The pump
Multistage horizontal pump (2 to 5 stages, depending on model)
Not self-priming.
Tapped ports, axial suction, radial discharge in upward direction.
Shaft sealing by standardized mechanical packing.
4.3 The motor
Ventilated motor with lengthened shaft end.
Protection index : IP 54
Insulation class: : F
10 bar
-10° to +70° C
up to 40°C (for higher temperatures,
get in touch with us)
depends on NPSH of pump
Single-phase motor: capacitor in terminal box, built-in thermal
protection with automatic reset.
FREQUENCY
SPEED rpm
1-phase
VOLTAGE
3-phase 230/400V(±10%) 220/380V(-10%) - 265/460V(+10%)
4.4 Accessories (optional)
• Suction kits • Isolating valves • Check valves • Foot valve-strainer
• Bladder or galvanized tanks • Anti-ram tank • Anti-vibration
sleeves • Motor protection circuit-breaker • Ordinary or stainless
steel weld-on PN25 counter-flanges • Stainless steel tapped PN16
counter-flanges • Dry-running protection (ME kit), etc. • ACSON
device for On/Off control and dry-running protection, etc.
5. INSTALLATION
Two standard cases:
• FIG. 1: Pump in suction
• FIG. 2: Pump under pressure from storage tank (item 9) or town
water supply (item 10), with dry-running protection system.
5.1. Installation
Install the pump in a place that is easy to reach, protected from
frost, and as close as possible to the place from which water is
drawn.
Install the pump on a foundation block or directly on a smooth, level
floor.
Pump attached by two holes for 8-mm-dia. studs.
Bear in mind that the altitude of the place of installation and
the water temperature may reduce the suction head of the
pump.
Altitude
Loss of head
0 m 0 mCL
500 m 0,60 mCL
1000 m 1,15 mCL
1500 m 1,70 mCL
2000 m 2,20 mCL
2500 m 2,65 mCL
3000 m 3,20 mCL
5.2. Hydraulic connections
By hose with spiral reinforcement or by rigid pipe.
The diameter of the suction piping must never be less than that of
the pump.
Limit the length of the suction pipe and avoid all features that cause
losses of head (tapers, bends, etc.).
This pipe, which will slope upward 2 %, must not let in any air.
If the pump is in suction (See FIG. 1) : immerse the strainer (20 cm
mini). Ballast the flexible pipe if necessary.
TYPE
Pumps 2 m3/h
Pumps 4 m3/h
Carefully seal the pipes with suitable products.
9
50Hz 60Hz
2900 3500
230V(±10%) 220V(-10%) - 240V(+6%)
Water
Loss of head
temperature
20 °C 0,20 mCL
30 °C 0,40 mCL
(40 °C) (0,70 mCL)
(50 °C) (1,20 mCL)
(60 °C) (1,90 mCL)
PORT ND (TAPPED)
SUCTION DISCHARGE
1" - (26-34) 1" - (26-34)
1 " - (33-42) 1" - (26-34)
1/4