Nice Neomat T Instrucciones Y Advertencias Para La Instalación Y El Uso página 9

02. Slowly press button ▼ the same number of times (1, 2,
x 1 = 5 Klux
x 2 = 10 Klux
3, 4 or 5) as the desired level.
x 3 = 15 Klux
x 4 = 30 Klux
x 5 = 45 Klux
03. After a few moments you will hear a number of beeps
x 1 = 5 Klux
x 2 = 10 Klux
equal to the required level.
x 3 = 15 Klux
x 4 = 30 Klux
x 5 = 45 Klux
04. Press and release button ■ to confirm.
If at point 3 you don't here the number of beeps equal to the desired level, simply do not
press anymore buttons and wait a few seconds for it to finish without changing the level.
4.3.8 - hanging the direction of movement in the event of rain
If using a rain sensor Nemo WSRT; when the sensor detects the presence of rain, it sends
the data to the motors and movement is activated in the programmed direction (the factory
setting is "up").
To modify the rain trip direction:
01. Press and hold ■ on a previously memorised transmitter until you hear a beep (after
approx. 5 seconds); then release.
02. Slowly press the same key ■ three more times.
03. Press the required direction key (up or down); the motor then emits 3 beeps = new
direction memorised.
Automatic movements generated by the "sun" sensor can be deactivated by a "Sun OFF"
command sent from a transmitter with this function (Ergo 4, Plano 4, WM004G) and can
be re-activated by means of a "Sun ON" command.
The automatic movements generated by the "sun" sensor can be accompanied at any
time by means of commands sent by the user via a normal transmitter; the latter have
priority over the "sun" sensor commands, as described in the following example: if
the awning is in position "1" (reached automatically when the "sun" threshold is exceed-
ed) and shortly afterwards the user sends a command for return of the awning to posi-
tion "0", in the next interval, even if the system continues to read values exceeding the
"sun" threshold, the awning is not moved (remaining in the position set by the user).
The "automatic cycle" interrupted by the manual command is restored when the bright-
ness level falls below the threshold (normally at dusk).
4.3.9 - Programming of the "FRT" function
After having programmed positions "0" and "1", position "2" can be programmed that
activates the retraction function FRT of the fabric.
Follow the indications in table "A11" to program position "2".
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A11" - Programming position "2"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Press and hold buttons ■ ▼ for another 5 seconds until 2
5s...
rapid beeps are heard. At this point the awning automatically
moves to the position of the lower limit switch (position "1").
03. Use buttons ▼ and ▲ within 5 seconds to position the
awning in the desired retraction position.
04. Confirm the position with button ■ of the transmitter
within 5 seconds until 3 beeps are heard. Afterwards the
awning will move to the lower programmed limit switch
position (position "1").
Note: if the programming described in point 4 is not confirmed the modifications are
aborted and the previous programming is maintained.
If after having programmed this function you wish to eliminate it, the procedure in table
A13 must be followed, omitting step 3 which would modify position "1".
When position "2" is programmed, the electronic control unit automatically calculates the
difference between positions "2" and "1", so that each time a lower command is given, the
awning lowers to the greater of the two positions and then retrieves the fabric until arriving
to the lesser of the two positions.
4.3.10 - Programming of the "FTC" function
After having programmed positions "0" and "1", position "S" can be programmed that
activates the "FTC" function for the automation of awnings with an automatic hooking
mechanism. Until the mechanism is working correctly, position "1" must be programmed a
few centimetres after the hooking point so that hooking occurs when retracting from point
"1", and position "S" is programmed a few centimetres after the release point so that the
ascent from point "S" is performed freely.
Follow the procedure indicated in table "A12" to program position "S":
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A12" - Programming the release position "S"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Press and hold buttons ■ ▼ for another 5 seconds until
5s...
2 rapid beeps are heard. At this point the awning auto-
matically moves to position "1".
03. Use buttons ▼ and ▲ within 5 seconds to position the
1
awning in the release position "S" (below position "1").
S
English – 7