Optional Programming - Nice Neomat T Instrucciones Y Advertencias Para La Instalación Y El Uso

4
Programming
The programming phase is divided into 3 parts:
1. Memorisation of the transmitters
2. Programming of positions "0" and "1"

3. Optional programming

The memorisation phases must be performed as indicated in table A1 to ensure that a
transmitter can control a NEOMAT-T motor.
WARNING:
• All the memorization sequences are timed, that is, they must be completed
within the programmed time limits.
• For transmitters with multiple "groups", choose the transmitter group the motor must be
associated with before proceeding with the memorization phase.
• Programming via radio may be done on all the receivers within the range of the transmit-
ter; therefore, only the one involved in the operation should be kept switched on.
It is possible to check if the motor already has transmitters memorized; this is done by
checking the number of beeps when the motor is switched on:
- 2 long beeps = No memorized transmitter.
- 2 short beeps = There are already transmitters memorized.
4.1 - Programming the transmitters
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A1" - Memorizing the first transmitter (in Mode I)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Connect the motor to the power supply, 2 long beeps
will be heard immediately.
02. Within 5 seconds press and hold button ■ of the trans-
3s...
mitter to be memorized (for approx. 3 seconds).
03. Release button ■ when you hear the first of the 3 beeps
confirming memorization.
See table A2 for the memorization of additional transmitters.
When one or more transmitters have already been memorized, others may be enabled as
shown in table A2.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A2" - Memorizing additional transmitters (Mode I)
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of the new transmitter (for
5s...
new
approx. 5 seconds) until you hear a beep then release it.
4 – English
02. Press button ■ of a previously memorized transmitter
x 3
old
slowly 3 times.
03. Press button ■ on the new transmitter again. Release
new
button ■ when you hear the first of 3 beeps, signalling
that memorization has been carried out.
Note: If the memory is full (14 transmitters), 6 beeps will indicate that the transmitter can-
not be memorized.
4.2 - Programming of positions "0" and "1"
A remote control memorised in Mode I must be used to program the positions. The manoeu-
vres will remain hold-to-run until positions "0" and "1" have been memorised in the control unit.
To begin with, the direction of the motor is not defined but after point 1 in table A3 has been
completed the direction of the motor is automatically assigned to the remote control buttons.
Follow the procedure in table A3 to program the "0" and "1" positions:
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A3" - Programming of positions "0" and "1"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold buttons ▲ or ▼ of a memorised remote
control until the awning is fully closed and the motor
automatically stops.
02. Press and hold button ▼ that lowers the awning.
03. Release button ▼ when the awning is in the desired
position ("1"). If necessary use the ▼ and ▲ buttons to
adjust the position.
04. Press and hold button ■ of the transmitter until you hear
5s...
a beep (after about 5 seconds) then release it.
05. Release and press again button 5 for another 5 seconds
5s...
until ■ rapid beeps are heard.
06. Press button ▼ until 3 beeps are heard and a short up
and down movement occurs indicating that the position
has been memorised.
4.3 - Optional programming
Optional programming is only possible after positions "0" and "1" have been programmed.
4.3.1 - Memorisation of the intermediate position "I"
When an intermediate position "I" is memorised the awning can be manoeuvred into the "I"
position by pressing the ▲ and ▼ buttons of the transmitter together.