User-Specific Menu; Other Welding Processes - LORCH ControlPro T Serie Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
14.5
User-specific menu
 Switch off the equipment at the main switch 10.
 Press the selection button on the left 32 and keep it
depressed.
 Switch on the equipment at the main switch 10
9 The user-specific menu is activated. The menu item
is shown in the 7-segment display 36.
9 The set value is shown in the 7-segment display 35.
 Press the selection button 32 or 33 to switch among
the menu items.
 Turn the control dial 34 to change the set value.
Menu
Menu item
no.
C00
Display and adjustment of the torch-ID.
See „Adjustment of the torch-ID" on page
46.
C01
Welding current limit for up/down torch.
When the welding current limit is switched
to "On", the welding current on the up/down
torch cannot be set higher than pre-select-
ed on the control terminal.
C02
Deactivation of the error message E05-00
(water pump) and of the water cooling unit
by LorchNet.
If the deactivation is switched "on", the
error message E05-00 (water pump) is no
longer displayed.
Also the water cooling unit is not switched
on by LorchNet.
Practical, e.g. for the use of an automatic
torch without plug or a cooling unit without
LorchNet.
C03
Activation of the orbital welding mode.
C04
ON: at short circuit the welding current
don't increase the adjusted welding current
shown in the display (set value).
Off: at short circuit the welding current is
increased on minimum 60 A.
C05
ON: by quick pressing of torch button 1
(start / stop) the 2nd torch button is simu-
lated.
(Second current on / off). Useful e.g. for
torches with one button only.
C06
ON: the current decrease (downslope) will
be - as adjusted – conducted, also if the
torch button is released (4th tact).
Off: at earlier release of the torch button
(4th tact) the current decrease (downslope)
is interrupted.
C07
On: PE conductor monitoring activated
Off: PE conductor monitoring deactivated
the PE conductor monitoring is an optional
available feature
- 46 -
Menu
no.
C08
Off: Using a foot remote control, the mini-
mum current (independent from the adjust-
ed welding current) in the TIG mode / AC at
electrode-Ø 1,0...2,0 mm = 10 Amps
electrode -Ø 2,4 mm
electrode -Ø 3,2 mm
On: the increased minimum current in the
TIG-mode / AC is deactivated
C10
Welding current limit
0 = Off
I1
...I1
Min
Setting
Tab. 6:

User-specific menu

values
 Switch the equipment off at the main switch 10 to
transfer the settings from the user-specific menu.
9...45
Adjustment of the torch-ID
Every torch of the i-LTG/i-LTW-series has an own torch-
On-Off
ID. This ID is related to the stress limits of the torch. If
the torch protection is activated (sub-parameter "tPr" =
on) in the TIG-mode, only a welding current according to
the maximum torch limit can be adjusted at the welding
machine.
On-Off
‰ The adjustment of the torch –ID is necessary for e.g.
if the torch pc-board was changed.
 Select in the user specific menu code-no. C00
 Adjust the required torch-ID at the turning knob 34,
according to the torch-ID-chart.
Type of torch
i-LTG 900
On-Off
i-LTG 1700
On-Off
i-LTG 2600
i-LTG 2800
i-LTW 3000
i-LTW 1800
On-Off
i-LTW 1800sc
i-LTW 2000
i-LTW 4500
Tab. 7:
Torch-ID
On-Off
 Press button „Save 58" to save.
9 The adjusted torch-ID is transferred to the torch.
14.6

Other welding processes

On-Off
MACS
1, 3
With the MACS (Modulated AC system) welding proce-
dure, the welding current is pulsed with alternating and
direct current.
 Select the desired mode with button 20.
909.1709.9-05
Menu item
= 15 Amps
= 20 Amps
= On
Max
Stress limits
Torch-ID
DC
9
125 A
17
150 A
26
200 A
28
300 A
30
320 A
18
350 A
19
400 A
20
220 A
45
450 A
Starting up
Setting
values
On-Off
0,
I1
...
Min
I1
Max
AC
80 A
120 A
160 A
250 A
220 A
250 A
320 A
165 A
360 A
04.19

Publicidad

Tabla de contenido
loading

Tabla de contenido