Starting Up; Electrode Welding Process; Tig Welding Process - LORCH ControlPro T Serie Manual De Instrucciones

14

Starting up

14.1

Electrode welding process

 Use button 20 to select the electrode mode (LED
electrode 21 lights up).
 Use the selection buttons 32 or 33 to select the pa-
rameter electrode diameter (LED 42 lights up).
 Use knob 34 to set the desired electrode diameter.
 Use the current mode selection button 27 to set the
desired current mode.
 Use the selection buttons 32 or 33 to select the pa-
rameter main current I1 (LED 43 lights up).
 Use the rotary knob 34 to set the desired current
intensity. If the current intensity does not match the
selected electrode diameter then the warning LED
lights 50 up. Nevertheless, it is possible to weld.
9 Your welding machine is now ready for use.
Electrode diameter [mm]
1,5
2,0
2,5
3,2
4,0
5,0
Heed the electrode manufacturer's instruc-
i i
tions.
Parameter
Hotstart IS
of main current
Hotstart time tS
Electrode diameter
T 180, T 220
T 250, T 300
Main current I1
T 180
T 220 AC/DC
T 220 DC
T 250
T 300
AC-balance
1
positive welding
AC-frequency
1
Tab. 2: Main parameters
Only for AC/DC
1)
- 42 -
Recommended current
intensity [A]
20 - 40
35 - 60
45 - 100
75 - 140
130 - 190
180 - 260
Factory
Range
setting
5 - 200 %
125
0 - 20 sec. 1
1,5 - 4,0 2,5
1,5 - 5,0
10 - 150 A
10 - 170 A
100
10 - 180 A
10 - 200 A
10 - 200 A
10 - 90 %
35
current
30 - 200 Hz 60
The factory setting values are optimised thanks to auto-
matic parameters.
You can use these factory settings unchanged for most
welding jobs.
Further fine adjustment facilities can be found in Chapter
„14.3 Secondary parameters" on page 44.
14.2

TIG welding process

 Select the desired mode with button 20.
– 2-stroke mode (LED 26 lights up).
– 4-stroke mode (LED 25 lights up).
– Spots mode (LED 23 lights up, only for 2-stroke).
– 2-stroke pulse mode (LED 22 and LED 26 light
up).
– 4-stroke pulse mode (LED 22 and LED 25 light
up).
 Use the selection buttons 32 or 33 to select the pa-
rameter electrode diameter (LED 42 lights up).
 Use knob 34 to set the desired electrode diameter.
 Use the current mode selection button 27 to set the
desired current mode.
 Use the selection buttons 32 or 33 to select the pa-
rameter main current I1 (LED 43 lights up).
 Use the rotary knob 34 to set the desired current in-
tensity. If the current intensity is not appropriate for
the selected tungsten electrode diameter, LED 50
lights up. Nevertheless, it is possible to weld.
9 Your welding machine is now ready for use.
HF ignition
LED/
Code
39
40
42
HF ignition is a contactless ignition brought about by
high-voltage impulses.
 Using the current type button, select 27 HF ignition
(LED HF 31 lights up).
43
Electrode
diameter
[mm]
47
1,0
1,6
2,0
2,4
3,2
909.1709.9-05
Danger due to electric shock!
If function HF-ignition (31) is selected,
a high ignition voltage is present at the
torch.
Never touch the welding electrode or parts
conducting welding current when the de-
vice is switched on.
Recommended Recommended
current inten-
sity DC
[A]
3 - 40 5 - 30*
15 - 130 20 - 90*
45 - 180 45 - 135*
70 - 240 70 - 180*
140 - 320 130 - 250*
Starting up
current inten-
sity AC
[A]
04.19