Mechanical Cooking Programmer; Digital Cooking Programmer - Franke SMART PLUS SGP 62 M /F Manual De Instalación Y Servicio

EN

Mechanical cooking programmer

(Fig. 1b)
End of cooking timer knob (B)
The end of cooking timer is a practical device that
turns the oven off automatically at a set time in an
interval of 1 to 120 minutes.
9 To use the end of cooking timer, the ringer must
be wound up by turning the knob (B) almost
one full turn clockwise; then, turning back,
set the required time by aligning the number
corresponding to the minutes with the fixed
reference on the front panel.
At the end of the set time, the ringer sounds
„ „
and the oven is automatically switched off.
Note: The oven stays hot
at around the set cooking
temperature for a long time
after it has been switched off;
therefore to avoid overcooking or
burning the food, it is advisable to
remove it from the oven.
Note: To use the oven in manual mode, i.e. without
using the end of cooking timer, align the knob (B)
pointer with the fixed symbol
When the oven is turned off, the end of cooking
programmer can be used as a normal timer.

Digital cooking programmer

(Fig. 1a)
It enables oven programming in the following modes:
– delayed start of cooking with set duration,
– immediate start of cooking with set duration;
– timer.
Setting the digital clock
When the appliance has been connected to the mains
or after a power failure the display will flash on: „0.00".
Press the + and - buttons
X X
together for a few
seconds. The time of day
can be adjusted with the
+ and - buttons, while the
dot between the hours
and minutes flashes.
If the time setting
„ „
mode is selected when an automatic
programme is active, the automatic
programme is cancelled.
Possible time adjustments can be made by repeating
the steps described above.
SGP 62 M _/F / SMP 62 M _/F / SMP 66 M _/F
B
on the front panel.
B
– 10 –
Acoustic signal frequency modification
The frequency of the acoustic signal can be changed
if a cooking cycle is not programmed (therefore the
display shows the time of day).
Press the + and - buttons (from the time
X X
modification menu) together.
Press Mode or Set to select the menu for
X X
modifying the acoustic signal frequency.
The acoustic signal frequency can be modified
X X
by repeatedly pressing the Mode or Set button;
„ton1", „ton2", „ton3" will appear on the display.
Manual oven operation
Once the time has been set, the programmer
automatically switches to manual mode.
Starting delayed cooking with set duration
When the time of the day is displayed, press the
X X
Mode or Set button twice to set a duration.
Then press it again to set the end of cooking time.
X X
Set the required time with the + and - buttons.
X X
During duration or end time adjustment mode
„ „
selection, the Auto symbol remains lit.
Once a programme duration is set, the end
„ „
time cannot be decreased.
Likewise, the duration of a programme cannot
„ „
be prolonged once the end time is set.
The end time and duration settings define
„ „
programme start time as follows:
start time = end time - duration.
After setting the duration and end time, the
„ „
display still shows the end time.
The programme starts when the time of day
„ „
coincides with the start time: the Auto symbol
lights up steadily and the symbol
flashing.
After the start of cooking, the display shows
„ „
the countdown. If only the end of cooking time
is selected (the duration is = 0), cooking starts
and the display shows the countdown.
The Auto symbol remains lit during the wait
„ „
for delayed start and for the entire duration of
cooking.
The symbol flashes during the wait for
„ „
delayed start and remains fixed when cooking
starts.
An acoustic signal sounds at the end of
„ „
cooking; to silence it, press any button or allow
the signal to continue for its duration.
D
C
starts