Turboair PERENNIAL BL Montaje Y Modo De Empleo página 15

Installation
The minimum distance between the supporting surface for the
cooking equipment on the hob and the lowest part of the
range hood must be not less than 45cm from electric cookers
and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
As described in the installation drawings perform 6 holes (8
mm diameter, 40 mm deep), in the positions shown in the
drilling template, to fix the hood support bracket and the
exhaust flue. After installation, check that the hood and
exhaust flue are perfectly aligned.
The range hood is intended to be installed over a hob
having 6 heating elements.
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided with
a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area, after
installation, apply a double pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in
accordance with installation instructions.
WARNING!
Before re-connecting the hood circuit to the mains supply and
checking the efficient function, always check that the mains
cable is correctly assembled.
Warning! If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid hazard.
Mounting
Before beginning installation:
• Check that the product purchased is of a suitable size for
the chosen installation area.
• Remove the charcoal (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
• Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.), eventually removing
them and keeping them.
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
Operation
First speed (T1)
Press T1 to activate the first speed. When the function is
activated, the LED turns on with a fixed light. Press T1 again
to turn the hood off.
Second speed (T2)
Press T2 to activate the second speed. When the function is
activated, the LED turns on with a fixed light. Press T2 again
to turn the hood off.
Third speed (T3)
Press T3 to activate the second speed. When the function is
activated, the LED turns on with a fixed light. Press T3 again
to turn the hood off.
Timer (T4)
The timer can be activated when the first, second or third
speed is active. When the function is activated, both the LED
of the Timer (T4) and that of the previously selected speed
(T1/T2/T3) turn on with a fixed light.
The duration of the timer depends on the selected speed:
First speed T1 = duration 20'
Second speed T2 = duration 15'.
Third speed T3 = duration 10'.
When a speed is timed, the timer can be deactivated by
pressing T4, or one of the other two inactive speeds. To turn
the hood off, press the speed again to which the timer had
previously been linked.
Light (T5)
The light can be activated at any time by pressing key T5.
When the function is activated, the LED turns on with a fixed
light.
Filter setting
Activation or deactivation of the filter indicators is only
possible with the hood off.
To access the configuration menu, hold pressed T2+T3, once
inside the menu T1 will start to flash.
The default setting is:
 grease filter indicator (T2) on, therefore active;
 odour filter indicator (T3) off, therefore not activated.
T2 activates/deactivates the grease filter indicator. T3
activates/deactivates the odour filter indicator. To exit the
menu, hold pressed T1 or wait 10''
Filter reset
The hood signals the need for filter maintenance at regular
intervals:
 grease filter every 40 hours;
8