Operating Instructions; Remote Control; Taking Into Operation; Switching Off - Truma Saphir vario Instrucciones De Uso

Operating instructions

Before starting to use the device, it is essential that the
Operating Instructions and "Safety instructions" be read
carefully! The vehicle owner is responsible for ensuring that
the device can be operated in the proper manner.

Remote control

+/– = Setting
Operating level,
Timer, Temperature
a = MODE
Operating mode
selector switch
FAN = Ventilation only
COOL = Cooling and
ventilation
b = FAN
Blowing power
LOW = Low
HIGH = High
c = TEMP.
Desired interior
temperature
16 °C to 31 °C
d = No function
e

= TIMER off

Set timer to 1 to 15 hours
f = RESEND
Send the settings of the remote control to device
again
g = ON / OFF
On / Off switch

Taking into operation

Before switching on, it is essential to make sure that the fuse
system for the power supply at the camp site is sufficient
(230 V):
600 W / 1.7 A
1500 W / 3.0 A
2000 W / 4.4 A
In order to prevent the power cable for the caravan from
overheating (minimum cross-section 3 x 2.5 mm²) the
cable drum must be fully unwound.
To carry out the individual switching commands, the remote
control must always be pointed at the infra-red receiver.
1. Switch the Saphir vario on using button "g" on the remote
handset. The "COOL MODE" that was previously selected
using the remote handset is automatically used.
2. Set the desired operating mode using the button "a".
FAN: Ventilation only (without cooling).
COOL: Cooling with 3 levels.
The blowing power and the interior temperature can be ad-
justed individually. The green indicator lamps on the receiver
indicate compressor operation and therefore cooling operation
with three levels.
600 W = LED 1 (COOL LOW),
1500 W = LED 2 (COOL),
2000 W = LED 1 + LED 2 (COOL HIGH)
COOL FAN
MODE MODE
COOL LOW TIMER
FAN LOW Hr.
COOL
FAN HIGH
COOL HIGH TEMP.
°C
a b
MODE
FAN
c e
d f
TEMP. TIMER RESEND
g
ON / OFF
Saphir vario
3. If necessary, adjust the fan speed and the room tempera-
ture to the required settings using buttons "b", "c", "+",
and "–".
When the room temperature that was selected using the
remote handset is reached in cooling mode, the compressor
switches off and the green indicator lamps in the receiver go
out. The circulation fan continues to run in order to provide
ventilation. If the room temperature is exceeded the device
automatically reverts to cooling mode.

Switching off

To switch off, press the button "g" on the remote control
once again.
If the air conditioning unit is switched on again within
approximately 3 minutes, the green indicator lamp blinks.
The air circulation fan runs, and the compressor activates itself
after 3 minutes.
Timer off
The air conditioning unit deactivation time can be set up to
15 hours in advance using the integrated timer, starting from
the current time.
To carry out programming, first switch the device to remote
control mode with the switch "g".
Then set the operating mode and the room temperature using
buttons "a", "b", "c", "+", and "–".
Then select the required deactivation time (1 – 15 hours) using
the "e" button (TIMER).
The programming is not active unless the air condi-
tioning unit is switched on. The remote handset can be
deactivated by covering the infrared transmitter on the front
of the remote handset. This prevents unintentional air con-
ditioning unit deactivation and accidental deactivation time
reprogramming.

IR receiver and manual on / off

There is an additional pushbutton on the receiver (m), with
which the unit can also be switched on and off without the
remote control (e.g. with a ballpoint pen).
Saphir vario
LED 3
LED 1
m
LED 2

Operating indicator

LED 1 green (600 W)
LED 2 green (1500 W)
LED 1 and LED 2 (2000 W)
LED 3 red – flashing – (data is being transmitted)
LED 3 red – permanently on – (fault)

Red LED illuminates

The unit is indicating a fault. Switch unit off, wait for a short
time and switch on again. If the red LED continues to illumi-
nate, please contact Truma Service.
If the unit is switched on using
this pushbutton, the system is
automatically reset to the fac-
tory settings (COOL, FAN HIGH,
TEMP. 21 °C).
13