Dip Switch Settings; Initial Start-Up; Safety Check; Start-Up Procedure - Webasto Next Manual De Instrucciones

The two cables from the ripple control receiver or the
floating contact must be inserted into this connector in
positions 3 and 4 (see Fig. 5). The two cables can be as-
signed to pos. 3 and 4 in any order. (max. cable cross
section 1.5 mm²).
WARNING
No voltage should be applied between terminals 3
and 4.

DIP switch settings

4.7
DANGER
High voltages.
Danger of fatal electric shock.
u
u Ensure safe isolation from the power supply.
DIP switches determine the maximum current. The cur-
rent can be adjusted in 1 A increments using the Charger
Setup app up to the maximum value that is configured by
the DIP switches.
Fig. 6
DIP switch left/ON = 1
DIP switch right/OFF = 0
DIP-switch factory setting:
D1 D2 D3 D4
Off
Off Off On
NOTE
Changes to the DIP switch settings become active
after restarting the charging station.
D1 D2 D3 [A] Description
0
0 0 32 Factory settings
0
0 1 10
1
0 0 13
1
0 1 16
0
1 0 20
0
1 1 25
1
1 0 8
1
1 1 0 Demo mode: charging not
possible
5111233B_ISI_Next
WARNING
The DIP switches must be adapted to the upstream in-
stallation by a qualified electrician.
D4 0= no unbalance load limit for single-phase
charging.
1= unbalance load limit at 16 A and D1-D3 >
20 A (for CH and AT).
D5 0= no unbalance load limit for single-phase
charging.
1= unbalance load limit at 20 A and D1-D3 >
25 A (for D).
D6 1= TN/TT system.
0= IT system (only single-phase connection
possible).
4.8

Initial start-up

4.8.1

Safety check

Document the results of the checks and measurements
carried out during initial start-up corresponding to the
applicable installation requirements and standards.
D5 D6
The Webasto Charger Setup app supports you with
checks during initial start-up.
On On
The local regulations relating to operation, installation
and environmental protection also apply.

Start-up procedure

4.8.2
1. Remove material residues from the connection area.
2. Check that every screw is correctly tightened and
every clamp is correctly engaged.
3. Fit the lower cover.
4. Secure the bottom cover with the mounting screws;
carefully tighten the mounting screws to the stop.
See Fig. 1.
5. Switch on power supply.
– Start sequence is activated (duration up to 60
seconds).
– White chase light running up and down. See Fig. 7,
operating status N2.
Fig. 7
1. Check initial start-up and record the measured values
in the test log. The Webasto Charger Setup app can
support you in carrying out and documenting this. An
EV simulator is used for the measurement at the
charging coupling.
2. Simulate and test the individual operating and pro-
tection functions with the EV simulator.
3. Connect the charging cable to the vehicle.
– The LED changes from green (N3) to pulsing blue
(N4), see Fig. 7.
5

Assembly

Fig. 8
Fig. 9
1 Hole for cable to *) The tools shown are not
building wiring sys- included in the scope of de-
tem livery of the wall box.
2 Hole for LAN cable

To replace the charging cable

6
DANGER
Danger of fatal electric shock.
Switch off and secure the power supply to the
u
charging station.
NOTE
Only use genuine Webasto parts.
NOTE
The charging cable may be replaced a maximum of
four times during the service lifetime of the Webasto
Next.
NOTE
If spare parts are required, please contact your install-
ation engineer or get in touch with the Webasto hot-
line.
See chapter 4.3.2, " Replace the charging cable" on page
17.
EN
19