Sime MURELLE HE 35 R ErP Manual De Instrucciones página 99

BOILER
. Instant.with.deviator.valve..
. and.flowmeter
.
. Instant.with.deviator.valve,..
.flowmeter.and.solar.combination
. D.H.W..tank.with.
.deviator.valve.and.boiler.sensor..
. vers..T.(LOW.INERTIA).
. On.board.D.H.W..tank.with
.deviator.valve.and.D.H.W..sensor...
. (LOW.INERTIA).
. R emote.D.H.W..tank.with.deviator.
. valve.and.D.H.W..thermostat...
. or.heating.only.vers..T/R.boiler
. (LOW.INERTIA)
. On.board.D.H.W..tank.with
.double.pump.and.D.H.W..sensor...
. vers..T/R.boiler.
. (LOW.INERTIA)
. On.board.D.H.W..tank.with
. double.pump.and.D.H.W..
. thermostat.vers..T/R.boiler...
. (LOW.INERTIA).
. Heating.only.with
. antifreeze.sensor...
. (LOW.INERTIA)
NOTE: the inside of the upper door of
the boiler panel has a label with the
values that have to be set for PAR 1 and
PAR 2 (fig. 19).
5
3.3.2 Warning
Should. the. boiler. operation. not. be. opti-
mal. but. no. alarm. sets. off,. press. the.
3
button.. .until.info.70.and.the.warning.
code.associated.to.the.ongoing.event.are.
1
displayed.
Once. optimal. operation. is. restored,. info.
70.will.display:."-.-".
Below.is.the.table.of.warning.codes:.
2
CODE DESCRIPTION
4
. E0. Reduced.capacity.operation.
. . (∆t.between.delivery.and.return.
. . over.40°C)
. E1. Shorted.external.sensor.(SE)
E2.
Preheating.function.active
. E3. TBD
. E4.
TBD
. E5. TBD
. E6.
TBD
. E7. TBD
. E8.
TBD
. E9. TBD
PAR 2
1
EXPANSION CARD
2
PAR.DESCRIPTION...
. .
40. Number.of.expansion.boards..
3
41. Mix.valve.stroke.time.
42. Priority.of.D.H.W..over.mixed.zone.
. .
43. Floor.drying.
4
. .
. .
. .
5
44. Type.of.solar.system.
∆
45. t.solar.collector.pump.1.
46. Solar.integration.delay..
47. Tmin.solar.collector.
48. Tmax.solar.collector.
6
PARAMETERS RESTORATION
PAR.DESCRIPTION...
8
. .
49.*. Reset.default.parameters.
. (par.01.-.par.02.=.."-")
9
* In case of difficulty in understanding the current setting or in case of an anomalous or
incomprehensible conduct of the boiler, we suggest to restore the initial values of the parameters
setting PAR 49 = 1 and the PAR 1 and PAR 2 as specified at point 3.3.1.
When the appliance is installed in sequence/cascade (modular
system with several generators) it is necessary to set on all the
boilers the following INST PAR parameters:
PAR 1 =
PAR 15 =
5
5
In addition, when the number of boilers in cascade is more than
two, configure the parameters OEM A1 of the MASTER boiler.
To access the OEM parameters press simultaneously the but-
tons ( and
press simultaneously he buttons (
1
1
seconds. At this point insert the access code formed by this
sequence of INSTALLATOR BUTTONS:
" + / - / < / > / < ".
2
2
Set the parameter:
PAR A1 = Number of cascade generators (3 ... 8)
PARAMETERS INSTALLER
RANGE.
.
0.....3.
0.....199.
0.=.Paralle.
1.=.Absolute
0.=.No.activated.
1.=.Curve.A
2.=.Curve.B
3.=.Curve.A+B
1.....8.
PAR.74.OEM.-.1....50.
"--",.0.....199.
"--",.-30.....0.
"--",.80.....199.
RANGE.
.
--.,.1.
CASCADE CONNECTION PARAMETERS
4 (for NATURAL GAS boilers)
12 (for PROPANE boilers)
0 for the first boiler (MASTER)
1 .... 7 for the other boilers (SLAVE)
(Avoid assigning the same number to SLAVE boi-
lers)
5
3
3
) for 2 seconds. Entered in the INST level again
1
2
4 4
UNIT.OF. INC/DEC.. DEFAULT
MEASUREMENT. UNIT. SETTING
=. 1.
10.sec.. 1.
=. =.
=. =.
=. 1.
°C. 1.
Min.. 1.
°C. 1. -.10
°C. 1.
UNIT.OF. INC/DEC.. DEFAULT
MEASUREMENT. UNIT. SETTING
=. =.
5
3 3
and ) for another 2
1
2
4
4
ES
PT
ENG
0
12
1
0
1
8
0
120
=
99