Milwaukee M18 BLLT Manual Original página 12

TECHNICAL DATA
Type
Production code
Voltage battery
No-load speed, low speed
No-load speed, high speed
Cutting line ø max.
Cutting capacity max.
Weight according EPTA-Procedure 01/2014 (2.0 Ah ... 12.0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise information: Measured values determined according to
EN 50636 / EN ISO 4871.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Always wear ear protectors!
Vibration information: Total vibration values (vector sum in the
three axes) determined according to EN 50636.
Vibration emission value a / Uncertainty K
h
Vibration front handle:
Vibration rear handle
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60335-1 / EN 50636-2-91 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING Read these instructions carefully, be familiar
with the controls and the proper use of the machine. Save all
warnings and instructions for future reference.
LINE TRIMMER SAFETY WARNINGS
Training
Read the instructions carefully. Be familiar with the controls and the
correct use of the machine.
Never allow children, persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge or
people unfamiliar with these instructions to use the machine, local
regulations may restrict the age of the operator.
Children being supervised not to play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
Keep in mind, that the operator or user is responsible for accidents
or hazards occurring to other people or their property.
Preparation
Before use, always visually inspect the machine for damaged,
missing or misplaced guards or shields.
Never operate the machine while people, especially children, or pets
are nearby.
Wear full eye and hearing protection while operating the product.
If working in an area where there is a risk of falling objects, head
protection must be worn.
22
M18 BLLT
Cordless Lawn Trimmer
491602 01 XXXXXX MJJJJ
18 V
0-4600 min -1
0-6200 min
-1
2,4 mm
400 mm
5,39 kg ... 5,85 kg
-18...+50 °C
M18B...; M18HB...
M12-18...; M1418C6
75 dB(A) / 3 dB(A)
95 dB(A) / 3 dB(A)
< 2,5 m/s 2 / 1,5 m/s 2
< 2,5 m/s / 1,5 m/s
2 2
Hearing protection may restrict the operator's ability to hear warning
sounds, pay particular attention to potential hazards around and
inside the working area.
Wear heavy long trousers, boots, and gloves. Do not wear loose
fi tting clothing, short trousers, jewellery of any kind, or use with bare
feet.
Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
Operation
Keep supply and extension cords away from cutting means.
Wear eye protection and stout shoes at all times while operating the
machine.
Avoid using the machine in bad weather conditions especially when
there is a risk of lightning.
Use the machine only in daylight or good artifi cial light.
Never operate the machine with damaged guards or shields or
without guards or shields in place.
Switch on the motor only when the hands and feet are away from
the cutting means.
Always remove the battery
- whenever the machine is left unattended
- before clearing a blockage
- before checking, cleaning or working on the machine;
- after striking a foreign object;
- whenever the machine starts vibrating abnormally.
ENGLISH
Take care against injury to feet and hands from the cutting means.
Always ensure that the ventilation openings are kept clear of debris.
Avoid using on wet grass.
Do not walk backwards when using the product.
Do not operate the product when there is a risk of lightning.
Do not expose the product to rain or wet conditions. Water entering
an appliance will increase the risk of electric shock.
Keep bystanders, children and pets 15m away from the area of
operation. Stop the product if anyone enters the area.
Keep the cutting attachment below waist level.
Keep hands and feet away from the cutting means at all times and
especially when switching on the motor.
Beware, the cutting elements continue to rotate after the motor is
switched off .
Beware of objects thrown by the cutting means. Clear debris like
small stones, gravel and other foreign objects from the work area
before starting operation. Wires or string may become entangled
with the cutting means.
The small blade fi tted to the lawn guard is designed to trim the
new extended line to the correct length for safe and optimum
performance. It is very sharp, do not touch it particularly when
cleaning the product.
Make sure the cutting head attachment is properly installed and
securely fastened.
Make sure all guards, defl ectors, and handles are properly and
securely attached.
Do not modify the product in any way, this may increase the risk of
injury to yourself or others.
Use only the manufacturer's replacement cutting line. Do not use
any other cutting attachment.
Do not use metallic cutting means
Immediately switch off and remove the battery pack in the event of
accident or breakdown. Don't operate the product again until it has
been fully checked by an authorised service centre.
Ensure that the cut-off blade is properly positioned and secured
before each use.
Before use and after any impact, check that there are no damaged
parts. A defective switch or any part that is damaged or worn should
be properly repaired or replaced by an authorised service facility.
Never operate the product unless all guards, defl ectors, and handles
are properly and securely attached.
Consider the environment in which you are working. Keep the
working area free from wires, sticks, stones, and debris which if
struck by the cutter can become thrown objects.
Maintenance and storage
Remove the battery before carrying out maintenance or cleaning
work.
Use only the manufacturer's recommended replacement parts and
accessories (see page 20).
Inspect and maintain the machine regularly. Have the machine
repaired only by an authorized repairer.
When not in use, store the machine out of the reach of children.
Never fi t a metal replacement line.
Stop the product and allow it to cool before storing or transporting.
Clean all foreign material from the product. Store it in a cool dry and
well-ventilated place that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and de-icing salts. Do
not store outdoors.
For storage, always remove the battery.
For transportation, secure the product against movement or falling to
prevent injury to persons or damage to the product.
ADDITIONAL SAFETY INSTRUCTIONS
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Injury caused by vibration
Hold the product by designated handles and restrict working time
and exposure.
• Exposure to noise can cause hearing injury
Wear ear protection and limit exposure.
• Injury due to fl ying debris
Wear eye protection, heavy long trousers, gloves and substancial
footwear at all times.
SPECIFIED CONDITIONS OF USE
The product is only intended for use outdoors by a standing
operator.
The product is designed for cutting grass, light weeds, and other
similar vegetation at or about ground level.
The cutting plane should be approximately parallel to the ground
surface when trimming.
The product should not be used to cut or trim hedges, bushes, or
other vegetation where the cutting plane is not at or about ground
surface level.
Do not use this product in any other way as stated for normal use.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
Battery protection for Li-Ion Akkus
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will vibrate for about 5
seconds, the fuel gauge will fl ash,and then the tool will turn OFF. To
reset, release the trigger.
ENGLISH 23