Milwaukee M18 BLLT Manual Original página 13

Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel gauge
will fl ash until the battery pack cooled down. After the lights go off ,
the work may continue.
Transport of Lithium Batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice.
OPERATION
To feed out the line, bump the trimmer head spool against the
ground gently while running a normal speed. NOTE: When used
near abrasive surfaces or in dense growth, the cutting line will wear
faster and require "bumping" more often.
CUTTING TIPS
Allow the ends of the line to do the cutting.
Contact between the line and solid objects will cause extra line wear
and breakage.
Do not drag the spool cover along the ground or bump it too hard.
Only bump spool on the ground. Do not bump against rocks,
driveways, etc.
Make multiple passes in long growth.
Avoid ornamental trees, shrubs, and plantings. Avoid contact with
siding, fence posts, etc. They can all be damaged by the trimmer.
REPLACING CUTTING LINE
Use only MILWAUKEE trimmer line (see technical data). Replace
the cutting line with either 6 m of 2,4 mm line or 7,6 m of 2 mm line.
Note, when used near abrasive surfaces or in dense growth, the
cutting line will wear faster.
For replacing cutting line see picture section.
24
Under normal operation, the remaining string should be thrown from
the spinning head during use. If any string remains in the head, or
to remove a length of string to replace with a diff erent type, turn the
trimmer head over and press the release tabs and pull the cover
away from the head.
2 1
1
Discard any short line remnants. Snap the cover back onto the
trimmer head.
TRANSPORTATION AND STORAGE
Always turn off the tool when transporting from one location to
another. Do not carry tool with fi nger on the trigger. Accidental start-
ing can cause serious personal injury.
Remove the battery and allow it to cool before storing or
transporting.
Carry the tool by the front handle to avoid accidental starting. Proper
handling of the tool will prevent injury.
For transportation in vehicles, secure the product against movement
or falling to prevent injury to persons or damage to the product.
Clean all foreign materials from the product. Store the product in a
cool, dry, and well-ventilated place that is inaccessible to children.
Keep away from corrosive agents, such as garden chemicals and
de-icing salts. Do not store outdoors.
Do not immerse in water or spray with a hose. Do not clean with a
pressure washer. Water entering a power tool will increase the risk
of electric shock. Store tool indoors.
Do not store the power tool on or near to fertilizers or chemicals.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Servicing requires extreme care and knowledge and should be
performed only by a qualifi ed service technician. For service, we
suggest you return the product to your nearest authorised service
center for repair. When servicing, use only identical replacement
parts.
Switch off and remove battery pack before conducting any
maintenance or cleaning work.
You may make adjustments and repairs described here. For other
repairs, contact the authorised service agent.
For replacement line, use only nylon fi lament line of the diameter
described in the specifi cation table of this manual.
After extending new cutter line, always return the product to its
normal operating position before starting.
After each use, clean the product with a soft dry cloth. Any part
that is damaged should be properly repaired or replaced by an
authorised service centre.
Check all nuts, bolts, and screws at frequent intervals for proper
tightness to ensure the product is in safe working condition.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
ENGLISH
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the machine.
Wear gloves!
Wear ear protectors!
Always wear goggles when using the machine.
Wear safety shoes!
Ensure that nobody is at risk of materials being
catapulted out or falling.
Keep distance.
Never expose tool to rain.
Beware of thrown or fl ying objects. Keep all
bystanders a safe distance away from the product.
Do not use metal blade(s) on the product.
WARNING - Disconnect battery before maintenance.
Parts or accessories sold separately.
The guaranteed sound power level shown on this label
is 96 dB.
96
Do not dispose of waste batteries, waste electrical and
electronic equipment as unsorted municipal waste.
Waste batteries and waste electrical and electronic
equipment must be collected separately.
Waste batteries, waste accumulators and light sources
have to be removed from equipment.
Check with your local authority or retailer for recycling
advice and collection point.
According to local regulations retailers may have an
obligation to take back waste batteries and Waste
electrical and electronic equipment free of charge.
Your contribution to re-use and recycling of waste
batteries and waste electrical and electronic equipment
helps to reduce the demand of raw materials.
Waste batteries, in particular containing lithium and
waste Electrical and electronic equipment contain
valuable, recyclable materials, which can adversely
impact the environment and the human health, if not
disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
n No-load-speed
0
V Voltage
Direct Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 25