Entering And Exiting The Contaminated Area - 3M Speedglas ADF G5-01 Instrucciones De Uso

6. Bluetooth®
The welding filter can be paired with and connected to iOS™ and Android™ devices via the 3M™ Connected Equipment App using Bluetooth®
(Fig. 15). The app can be downloaded from the iOS™ App Store® or Google Play™ store. For information on how to connect the app with the
welding filter, follow the User Instructions in the app. When connected to the iOS™ or Android™ device, the user will have access to welding filter
settings, work statistics, etc.
7. Low Battery Indicator
The battery should be replaced when the low battery indicator flashes or LEDs do not flash when the buttons are pressed (Fig. 16a and 16b). See
the "Inspection & Maintenance" section for information regarding removing the ADF and replacing the battery.
MADE IN SWEDEN BY 3M

ENTERING AND EXITING THE CONTAMINATED AREA

1. This product meets the requirements of certain industrial eyewear standards. It does not provide complete head, eye, and face protection from
significant impact and penetration and are not a substitute for good safety practices and engineering controls. Misuse may result in serious
bodily injury or death. For correct use, consult your supervisor and User Instructions or contact 3M Technical Service in the U.S.A. at
1-800-243-4630. In Canada, call Technical Service at 1-800-267-4414.
2. When exposed to eye and face hazards, wear additional eye and/or face protectors appropriate to the hazard. ANSI Z87.1-2015 – Occupational
and Educational Eye and Face Protection, incorporated by reference in the OSHA Eye and Face Standard 29 CFR 1910.133, suggests safety
spectacles or goggles should be worn in conjunction with loose fitting respirators if the visor can be raised from the normal position during use.
Failure to do so may result in serious bodily injury or death.
3. Failure to follow these instructions may reduce respirator performance, overexpose you to contaminants, and may result in serious bodily
injury, sickness or death. The 3M™ Speedglas™ Heavy-Duty Welding Helmet G5-01 is one component of an approved respiratory protection
system. Always read and follow all User Instructions supplied with your 3M™ Speedglas™ Heavy-Duty Welding Helmet G5-01, PAPR blower
unit or Supplied Air (SA) device in order to ensure correct system operation.
4. Failure to follow these instructions may reduce the capability of the 3M™ Speedglas™ Heavy-Duty Welding Helmet G5-01 shell to
withstand impact and penetration and may result in serious bodily injury or death.
5. Do not use in high heat environments above the recommended maximum temperature.
6. This welding helmet must not be painted or cleaned with solvents. Any decals applied to the welding helmet must be compatible with the
surface material and known not to affect adversely the characteristic of the materials used in the welding helmet. Decals may affect the impact
and flammability characteristics of this welding helmet and prevent inspection of damage under decals.
7. Any headgear subjected to significant impact should be replaced.
8. Failure to follow these instructions may reduce the capability of the 3M™ Speedglas™ Heavy-Duty Welding Helmet G5-01 clear grinding
visor to withstand impact and penetration and may result in serious bodily injury or death.
9. Severe burn injuries may result if this welding helmet is used for heavy-duty overhead welding applications where there is a potential for
falling molten metal.
With the Powered Air Purifying Respirator (PAPR) assembly or supplied air (SA) respirator system in operation, enter the contaminated area, breathing
normally. If using an SA system, keep the air hose away from equipment, vehicles, and other physical and chemical hazards.
1. Airborne contaminants which can be dangerous to your health include those that are so small you may not be able to see or smell them.
2. Do not wear this respirator to enter areas where:
a. Atmospheres are oxygen deficient.
b. Contaminant concentrations are unknown or cannot be adequately estimated.
c. Contaminant concentrations are Immediately Dangerous to Life or Health (IDLH).
d. Contaminant concentrations exceed the maximum use concentration (MUC) determined using the Assigned Protection Factor (APF) for the
specific respirator system or the APF mandated by specific government standards, whichever is lower.
3. Leave the contaminated area before reaching inside or removing the welding helmet. Do not remove the respirator or reach your hand into the
welding helmet in areas where the air is contaminated. Air routing adjustments may be made while in a contaminated area.
AUTO
ON
Fig. 16a
®
Fig. 15
W WARNING
15
Fig. 16b