COMMISSIONING AND USE
SET CLOCK
The SET CLOCK menu allows for setting the day, time and current
date.
The
or
can be used to modify the selected value. With the
+
-
button the user can select the next value, while with the
the previous value is selected.
The
button can be used to return to the previous menu.
O
TUESDAY
1
2
10:20
4
14/03/2018
1 Day of the week (full name)
2 Hour
3 Minutes
4 Day
5 Month
6 Year
LANGUAGE
The LANGUAGE menu allows for selecting the dialogue language
among various options: Italian, English, French, German and Spanish.
SETTINGS
The SETTINGS menu allows for adjusting the main remote control
settings. The table below summarises the possible settings and their
meaning.
Menu
Meaning
Enables/disables the beep
BOARD BEEPS
on the power board
Adjusts the time that the
BACKLIGHT ON
display remains illuminated
Adjusts the time that the
DISPLAY ON
display remains on
Enables/disables the
BRIGHTNESS
illumination of the display
DISPLAY
Adjusts the display contrast 15÷60
CONTRAST
Enables/disables the beeps
KEY BEEPS
every time the remote
control keys are pressed
(*) The life of the remote control batteries varies in relation to the
chosen settings.
CS.SB80.IST_EN_Rev. 2.0_09-23
INITIAL LOAD
The INITIAL LOAD menu allows for pre-loading pellets for 90 seconds,
when the appliance has been switched off and has cooled down.
This function may be useful if the appliance is switched on after the
s
button
tank has been completely emptied, or when it is filled for the first time.
E
The function starts by pressing the
the
button.
O
a
WARNING: once the operation has been completed,
before switching on the appliance you should re-
move any pellets accumulated inside the brazier.
3
STOVE STATUS
5
The STOVE STATUS menu allows for instantly viewing the status of
the appliance, by showing the operating conditions of the various de-
6
vices connected to it. Several pages are displayed in succession.
The table below shows the possible statuses of the devices and their
Fig. 29
meaning.
Status
L04-270218
(example)
AIR 1.0
(example)
T.SMOKE
T.ROOM
T.ROOM 1
Settable val-
ues (*)
ON/OFF
2–10 sec
T.ROOM 2
15–60 sec - ON
ON/OFF
ASP.RPM
LOAD
ON/OFF
STATUS T.A.
AIR SPEED
DUCT. 1
DUCT. 2
button and stops by pressing
+
Meaning
Code of the firmware loaded in the control unit.
Code of the firmware loaded in the remote
control.
Indicates the temperature measured by the probe
inside the combustion chamber.
Indicates the room temperature measured by the
probe on the remote control.
If a temperature sensor is connected, it indicates
the ducted 1 room temperature measured by the
device.
If a room thermostat is connected, it indicates
the latter's status: (OFF = Room thermostat
contact OPEN = Thermostat not triggered; ON =
Room thermostat contact CLOSED = Thermostat
triggered)
If a temperature sensor is connected, it indicates
the ducted 2 room temperature measured by the
device.
If a room thermostat is connected, it indicates
the latter's status: (OFF = Room thermostat
contact OPEN = Thermostat not triggered; ON =
Room thermostat contact CLOSED = Thermostat
triggered)
Indicates the speed of the fume extractor.
Indicates the pellet loading interval.
Indicates the status of the main room thermostat
(OFF = Room thermostat contact OPEN =
Thermostat not triggered; ON = Room thermostat
contact CLOSED = Thermostat triggered)
Indicates the speed of the front air fan.
Indicates the speed of the air in ducted room 1.
Indicates the speed of the air in ducted room 2.
EN
25