Explanation Of The Programme Commands; Access To The Submenus - FAS BABY Manual De Instrucciones

BABY FAS – Issue 04
8.3

EXPLANATION OF THE PROGRAMME COMMANDS

8.3.1

ACCESS TO THE SUBMENUS

Command 01 Machine test:
This is used to perform the test relative to the various selections. By keying in 01 followed by key B, the
message "Selection nr.
motors) and press B. The machine will check the selections that are effectively present (Test 12). If the
number found does not correspond to the value set, the message " CONFIG ERROR" appears on the
display. This indicates that one or more of the selections is not connected electrically. In this case, check the
wiring. If however the number of the selections found corresponds to the value set, 3 vending cycles for each
selection are performed. If during this phase, an anomaly in the function of a selection is encountered, the
test is blocked and the corresponding selection code remains visualised on the display. If the test is
performed successfully, the machine returns to the main programming menu (command 00).
Command 02 Calls submenu for setting the clock & daily timers:
Key in 02 and press the B pushbutton to enter the submenu for setting the clock and daily timers. Alarm 00
will appear on the display. Follow the method described in the specific section to display and alter the
parameters.
Command 03 Calls submenu for setting prices:
Key in 03 and press B to enter the submenu for setting the prices per selection. "Selection number 00" will
appear on the display. Key in the selection you want to display or to modify the price and press the B
pushbutton. "Price....." will appear on the display. Key in the new value of the price and press again B to
confirm the change. Press pushbutton A to return to the main menu if no alteration is required.
To set price of selection 16 to 40 pence, proceed as follows:
1. Go into programming mode to display........................................................................................ Command 00
2. Key in 03 and press B to display .................................................................................... Selection number 00
3. Key in 16 and press B to display the present value of the price .................................................. Price NNNN
5. Set value to 40 and press B.
Command 04 Calls submenu for setting discounted prices:
This command has the same functions as command 03, but it shows the discounted prices.
In the MDB mode, these prices refer to key or credit card purchases or purchases made within a certain time
band, or both (see description Command 61). Furthermore, if the MDB cashless system allows the product to
be selected from two different price tables, this command is used to set the prices relative to table 2. The
prices relative to table 1 are set at Command 03.
Command 05 Call submenu setting references to prices:
This command is only used when the prices are set on the coin mechanism.
Key in 05 and press B to enter the submenu for setting references to prices. "Selection number 00" will
appear on the display. This submenu allows to associate to each selection a number of price. Key in the
code which identifies the selection and press B. The number of the price associated with the chosen
selection will appear on the display. Key in the number of the new price you wish to associate with the
selection and press B to confirm the change. Press A to return to the submenu and the previous value will be
memorized. Repeat this procedure for another selection or press A to return to the main menu.
For example to associate to spiral 53 the price number 10, proceed as follows:
1. Go into programming mode to display........................................................................................ Command 00
2. Key in 05 and press B to display ............................................................................................ Selection No.00
3. Key in 53 and press B to display the present value of the parameter............................................... No. price
4. Key in 10 and press RET.
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI) – tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: info@fas.it
00" appears. Set the number of the selections present in the machine (number of
21
E
N
G
L
I
S
H