Metabo HPT C3612DRA Manual página 6

English
SPECIFIC SAFETY RULES FOR USE OF
THIS POWER TOOL
WARNING
The following specific operating instructions
must be observed when using this POWER TOOL
in order to avoid injury:
DO's
ALWAYS OBSERVE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Review this Manual and familiarize yourself with the
safety rules and operating instructions for this
POWER TOOL before attempting to use it.
2. Remove all packing materials attached or connected
to the tool before attempting to operate it.
3. Always confirm that the POWER TOOL is clean
before using it.
4. Always wear snug-fitting clothing, non-skid footwear
(preferably with steel toes) and eye protection when
operating the POWER TOOL.
5. Always handle the POWER TOOL carefully. If the
POWER TOOL falls or strikes against a hard object, it
might become deformed or cracked or sustain other
damage.
6. Always cease operating the saw at once, if you notice
any abnormality whatsoever.
7. Always confirm that all components are mounted
properly and securely before using the tool.
8. When replacing the saw blade, always confirm that
the rpm rating of the new blade is correct for use on
this tool.
9. Always shut off the power and wait for the saw blade
to completely stop rotating before doing any
maintenance or adjustments.
10. During slide cutting, always push the saw blade away
from the operator.
11. Always clamp or otherwise secure the workpiece to
the fence; otherwise the workpiece might be thrust
form the table and cause bodily harm.
12. During miter or bevel cutting, always wait for the
rotation of the blade to stop completely before lifting
the saw blade.
13. Always make a trial run first before attempting any
new use of the saw.
14. Always handle the saw blade with care when
dismounting and mounting it.
15. Always confirm that the workpiece is free of nails or
other foreign objects before beginning a cut.
16. Always keep your hands out of the path of the saw
blade.
17. Always confirm that the lower guard is in the proper
place before using the saw.
6
18. Always confirm that the lower guard does not obstruct
the sliding motion of the saw before attempting slide
cutting.
19. Inspect the tool power cords periodically.
20. Always confirm that the proper lengths and types of
extension cords are being utilized, if necessary,
before starting the tool.
21. Always confirm that the motor air vents are fully open
before using the tool.
22. Always wait until the motor has reached full speed
before starting a cut.
23. Always keep the handles dry, clean and free of oil and
grease. Hold the tool firmly when in use.
24. Always use outboard stands to provide support for
long workpieces that overhang the table of the slide
compound miter saw.
25. Always operate the tool after ensuring the workpiece
is fixed properly with a vise assembly.
26. The operating instructions provided with the tool shall
direct the user to secure the tool to supporting
structure if, during normal operation, there is a
tendency for the tool to tip over, slide, or walk on the
supporting surface.
27. Ensure before each cut that the machine is stable.
28. If the saw blade should become jammed, switch the
machine off and hold the workpiece until the saw
blade comes to a complete stop. To prevent
kickback, the workpiece may not be moved until after
the machine has come to a complete stop.
Correct the cause for the jamming of the saw blade
before restarting the machine.
29. Use only saw blades that are marked with a maximum
permitted speed equal or higher than the no-load
speed marked on the POWER TOOL.
30. Use only a saw blade diameter in accordance with the
markings on the POWER TOOL.
31. Replace the table insert when worn.
DON'Ts
NEVER VIOLATE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Never operate the POWER TOOL unless you fully
understand the operating instructions contained in
this Manual.
2. Never leave the POWER TOOL unattended without
first removing the battery from the main body.
3. Never operate the POWER TOOL when you are tired,
after you have taken any medications, or have
consumed any alcoholic beverages.
4. Never use the POWER TOOL for applications not
specified in the instruction manual.
5. Never operate the tool while wearing loose clothing, a
necktie or jewelry, or while your hair is uncovered, to
protect against getting caught in the moving
machinery.