Metabo HPT C3612DRA Manual página 8

English
15. Definitions for symbols used on this tool
V.......................................................................... volts
A ................................................................... amperes
Hz ....................................................................... hertz
W.......................................................................... watt
or DC ................................................ direct current
or AC...................................... alternating current
n
0
......................................................... no load speed
---/min............. revolutions or reciprocation per minute
min ................................................................. minutes
REPLACEMENT PARTS
When servicing use only identical replacement parts.
Repairs should be conducted only by a metabo HPT
authorized service center.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER OR ADAPTER
The term "charger or adapter" in the safety instructions
refers to your battery charger or AC/DC adapter.
WARNING
Death or serious bodily injury could result from
improper or unsafe use of charger or adapter. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YSL3 or
AC/DC adapter Model ET36A.
2. Before using charger or adapter, read all instructions
and cautionary markings on (1) charger or adapter,
(2) battery, and (3) product using battery.
3. When charging the battery with a battery charger,
reduce the risk of injury by charging metabo HPT
rechargeable battery multi volt type series and
BSL18 series. Other type of batteries may burst
causing personal injury and damage.
4. Do not expose charger or adapter to rain or snow.
5. Use of an attachment not recommended or sold by
the charger or adapter manufacturer may result in a
risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting charger or adapter.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
8. An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock.
If extension cord must be used make sure:
8
a. That blades of extension cord are the same
number, size, and shape as those of plug on
charger or adapter:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger or adapter as specified in
Table 1.
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR CHARGER OR ADAPTER
AC Input Rating
Amperes * 1
Equal to
or but less
greater than
than
0 2
2 3
3 4
*1 If the input rating of a charger or adapter is given in
watts rather than in amperes, the corresponding
ampere rating is to be determined by dividing the
wattage rating by the voltage rating–for example:
1,250 watts
125 volts
9. Do not operate charger or adapter with damaged cord
or plug-replace them immediately.
10. Do not operate charger or adapter if it has received a
sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
11. Do not disassemble charger or adapter; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
12. To reduce risk of electric shock, unplug charger or
adapter from receptacle before attempting any
maintenance or cleaning. Removing the battery will
not reduce this risk.
13. This AC/DC adapter is for use only with specific tools,
including C3612DRA. The adapter might be suitable
for use with other metabo HPT battery operated tools.
It is necessary to confirm suitability by referencing the
instruction manual of the specific tool or by consulting
our web site https://www.metabo-hpt.com/. Failure to
confirm suitability before using the adapter with
specific tools could result in fire hazard.
AWG Size of Cord
Length of Cord, Feet (Meter)
25 50 100
(7.5) (15) (30)
18 18 18
18 18 16
18 18 16
= 10 amperes
150
(45)
16
14
14