GLOBBER E-MOTION 14 Manual Del Propietário página 10

• Check that the kick stand is fully folded before starting. When parking, check that the kickstand is properly unfolded; the unit must
be parked on a flat ground to avoid any risk of falling. If the unit is not equipped with a kickstand, ground parking is recommended,
ensuring you do not interfere with the traffic.
• It is highly recommended to wear reflective clothing and accessories to enhance/increase its visibility.
• When the product is no longer in use, it should be stored in a safe place or put under protection (lock system) to prevent
unauthorized use of commands/product.
• Vibration and shock: Using an electric scooter can generate significant vibrations and shocks, depending on of the surface on
which it is used. Do not use your scooter for too long, and immediately stop using if discomfort caused by vibrations. The total
hand-arm vibration value does not exceed 2.5m/s
• In case of fall or accident, always check that product is switched off and clear the way for other users if possible.
• The front suspension in steering column absorbs vibration.
• The materials used for the construction of the machine, are not toxic, and have been analysed according to the following directive:
2011/65/EU Rohs. A safety data sheet has also been established for the battery.
• The safety and reliability of the control systems have been evaluated according to the following guidelines: 2014/30/EU
Electromagnetic Compatibility Directive and 2014/35/EU Low Voltage Directive.
• In France this product is equipped to circulate on certain public roads, for the users of at least 14 years old. Consult the website:
service public.fr/particuliers/vosdroits/F308.
• In France, it is the responsibility of users of a motorized mobility device (EDP) to insure. Motorized EDPs may be included in home
multi-risk insurance contracts but with a specific civil liability clause of the land motor vehicles (VTM) type, or be the subject of a
specific EDP motorized contract.
• To avoid pinching and entrapment, do not get your fingers stick in moving parts.
7 – MAINTENANCE
• Warning. As with any mechanical component, your vehicle is subject to high stresses and wear. The various materials and
components may react differently to wear or fatigue. If the expected service life for a component has been exceeded, it may break
suddenly, thereby risking causing injuries to the user. Cracks, scratches, and discoloration in the areas subject to high stresses
indicate that the component has exceeded its service life and should be replaced.
• Caution: The rear wheel has a motorised part. If you wish to check the motorized parts or change it, contact a qualified technician
or a Globber representative at contact@globber.com.
• Eliminate the sharp edges generated by the use.
• Do not modify or transform the vehicle, including the steering tube and sleeve, stem, folding mechanism and rear brake. or the
warranty will be invalidated.
• The accessories and any additional items which are not approved by the manufacturer shall not be used.
• To clean: Disconnect the charger and turn off the product, wipe it with a dry cloth.
• The lithium battery: To guarantee the battery lifetime, charge it when its level is low. If it is not used for a long period of time, you
are advised to charge it once a month. If you wish to check the battery or change it, contact a qualified technician or a Globber
representative at contact@globber.com.
• The recommended storage temperature for the battery is between 5°C and 30°C.
• Do not use or place the electric scooter in an environment where the temperature exceeds 40°C to avoid any lithium battery
malfunction that may lead to it catching fire.
• Never store the electric scooter in a car during hot weather to avoid any danger of this.
• Bearings: Avoid riding through water, oil, or sand, which would damage your bearings. To maintain your bearings, check regularly
that the front wheel turns properly by turning the electric scooter upside down and pushing the wheel with your fingers. If the
front wheel does not turn, remove it and check the condition of the bearings. First unscrew the wheel axle. Remove the axle and
remove the wheel. Carefully push the two bearings out of their seating. If they are chipped or crushed, buy new ones. If there is no
visible damage, oil them. To do so, remove any traces of grease, mud, or dust from the bearing using a paper towel or a cloth then
grease them either with a self-lubricating spray or by soaking them in oil overnight (turn the bearings several times in the oil before
leaving them to soak). Refit the bearings and axle, then the front wheel.
• The wheels: The wheels wear out ove a certain length of time or may even develop holes if the scooter is used on rough surfaces
too often. This is particularly true of the rear wheel on which the brake is applied. Check them regularly and have them changed for
better safety.
• Product modifications: The original product must by no means be modified except for the maintenance-related changes mentioned
in these instructions.
• Nuts, axles and other self-locking fasteners: These should also be checked regularly. They can become loose after a while in
which case they should be tightened. They can become worn and not tighten properly, in which case they should be replaced.
ENGLISH
10
.
2