Kärcher SE 4 Manual Del Usuario página 16

5. Fit the device head, see chapter Fitting the device
head.
6. Install the fresh water tank, see chapter Installing
the fresh water tank.
Ending operation
Note
To ensure that no cleaning particles and dirt particles re-
main in the lines, perform cleaning (without the addition
of detergent) after each application.
1. Flush the spray lines in the device.
a Fill the fresh water tank with about 1 litre of clear
water.
b Press the switch for spraying.
The lamp on the switch lights up and the pump
starts
c Hold the spray/suction hose over a drain until the
clear water has been used up.
2. Switch off the device, see chapter Switching off the
device.
3. Disconnect the accessory, see chapter Disconnect-
ing accessories
4. Remove the remaining liquid in the spray/suction
hose.
a Press the unlocking button and remove the
spray/suction hose from the device.
b Press the lever on the handle of the suction hose
and allow the liquid to flow out.
Illustration V
Note
To allow the liquid to dry completely, do not wrap the
spray/suction hose around the device to dry.
Note
To avoid puddles in the living area (e.g. on carpet, par-
quet), let the remaining liquid run in a suitable container
(e.g. sink, bucket).
5. Clean the accessory part individually under running
water and then allow them to dry.
Note
Any residual water may drip out, therefore it is best to
place it in the shower or bath tub.
6. Empty the container, see chapter Emptying the con-
tainer.
7. Thoroughly rinse the container with clear water.
8. If necessary,e.g. if the sieve in the fresh water tank
is soiled, rinse the fresh water tank with clear water,
see chapter Cleaning the sieve in the fresh water
tank.
9. Leave the device open to dry.
10. After complete drying, attach the spray suction
pipes to the accessory holder.
11. Store the device in a dry and frost-proof room.
Care and service
General care instructions
 Clean the device and plastic accessory parts with a
commonly available plastic cleaner.
 Rinse the container and accessories with water, as
necessary, and dry them before further use.
Cleaning the cartridge filter
Note
If necessary, carefully wipe the cartridge filter with a
damp cloth.
1. Take off the device head, see chapter Fitting the de-
vice head.
16
2. The filter can be unlocked and removed by turning it
towards the symbol
Illustration AB
3. Do not rub or scrub the filter when cleaning it.
4. Allow the filter to dry completely before using it
again.
Illustration AC
5. Reinsert the cartridge filter:
 Install the filter on the filter basket, turn it towards
the symbol
rectly.
Illustration AB
Cleaning the spray nozzle
Note
If the spray jet is uneven, the spray nozzle of the wash-
ing suction accessory can be damaged by residues and
will need to be cleaned.
1. To clean the wash floor and wash upholstery nozzle,
loosen the nozzle fastener by turning it and pull it out
together with the spray nozzle.
Note
Keep the O-ring/sealing ring in a safe place and reinsert
it after cleaning.
Illustration AD
2. Clean residues in the spray nozzle under running
water.
3. Insert the spray nozzle into the nozzle fastener and
fasten it again by turning it.
4. Also clean residues in the spray nozzle of the wash
crevice nozzle under running water.
Cleaning the sieve in the fresh water tank
Note
On the bottom of the fresh water tank there is a filter on
which dirt particles can settle and thereby obstruct the
water flow.
Therefore, regularly rinse out the fresh water tank.
1. Remove the fresh water tank, see chapter Remov-
ing the fresh water tank.
2. Clean the sieve.
a Fold the tank cap up.
b Release the lock.
c Remove the water hose from the tank.
The sieve is located at the end of the water hose.
d Clean the sieve under running water.
3. Rinse the fresh water tank with clear water.
Illustration AE
4. Insert the sieve.
5. Lock the fresh water tank.
6. Install the fresh water tank, see chapter Installing
the fresh water tank.
Troubleshooting guide
No water emitted from the nozzle
Fresh water tank empty
 Fill up the fresh water tank.
Fresh water sieve is dirty,
 Clean the fresh water filter.
Fresh water tank not installed correctly.
 Install the fresh water tank correctly.
Connection between accessory and spray/suction hose
not correct.
 Establish the correct connection.
Detergent pump defective,
 assign Customer Service.
Spray jet uneven
English
.
and make sure it is attached cor-