General Safety Standards - Aprimatic WING NK Manual De Instrucciones

General safety standards

2. GENERAL SAFETY STANDARDS
Carefully read the instructions before starting to install the
product.
!
Warning
Packing materials (plastic, polystyrene, etc.) must not be
dispersed in the environment and must not be left where
children can find them as they are a potential source of
danger.
INCORRECT INSTALLATION OF THE UNIT MAY CAUSE
SERIOUS DANGER. FOLLOW ALL THE INSTALLATION
INSTRUCTIONS CAREFULLY.
Only professionally qualified personnel should install the
product. We recommend operating in a well-lit and healthy
environment, in compliance with the safety regulations in
force. We recommend the use of approved protective clothing
(safety shoes, protective goggles, gloves and helmet). Do not
wear articles of clothing that could get caught. Take adequate
safety measures to prevent the risk of injury caused by
sharp splinters and the possible risks of crushing, knocks
and cuts or amputation. We recommend strict observation
of the national regulations for safety in work sites (in Italy,
Legislative Decree 528/99 coordinated with Legislative
Decree 494/96 "Implementation of Directive 92/57/EEC
concerning the minimum rules and regulations on health and
safety at work to be observed when working on temporary
or mobile sites").
Information
You may consult the Safety Guide for installing pedestrian
sliding doors on our website: www.aprimatic.com.
Cordon off the yard to prevent any unauthorised persons from
passing through the working area. Do not leave the working
area unattended. Installation, electrical connections and
adjustments must be carried out in a professional manner in
compliance with the Good Manufacturing and Workmanship
regulations in force in the country where the automation is
installed. The manufacturer of the device is not responsible for
the non-observance of professional standards of work in the
construction of the power-driven structure, nor for any damage
which may be caused by the use of the drive.
Incorrect installation may be dangerous.
Follow the manufacturer's instructions.
Before starting the installation, check the product is intact and
that the existing structure is suitably strong and stabile. Also
ensure it complies with current standards for the sector. The
230V electrical system supplying power to the automation
must be installed by an expert and qualifi ed electrician, in
accordance with national standards of the installation country
(for Italy Law 46/90). before carrying out any maintenance
or repairs or replacing any parts, whether mechanical
or electrical, disconnect the mains power supply. Before
connecting the electrical mains make sure that the data on the
rating plate corresponds to the specifi cations of the electric
mains supply. The protective measures on the primary coil
must be adopted on site. Use a 6A differential switch-overload
30 mA as main switch. Arrange and fasten cables with the
special clamps.
Only specialised technicians, trained to do the job, should
test and put the door into service, as well as carrying out the
periodic checks and any maintenance.
Information
We strongly recommend following a specialised training
course. Installers should contact the supplier for information
on courses.
Caution
The automation cannot be tested and put into service until
the sliding door has been verified as complying with the
standards of MACHINERY DIRECTIVE 89/392/EEC, to which
the complete door, fi tted and installed, is subject. The installer
must at all times use and keep the TECHNICAL DOSSIER
of the automatic door and must follow all of the provisions
contained in it.
At the end of the work the installer must check the installation
has been carried out correctly and the automation works
properly.
THE RISKS connected to the operation of the sliding door
MUST BE ASSESSED making sure there are no dangerous
crushing or shearing points. If necessary special preventive
measures must be taken and all of the signs required by
the regulations in force to warn of any dangerous zones
must be attached.
Every installation must clearly indicate the ID data for the
power-driven system.
The installer must provide all the information about the
automatic, manual and emergency functioning of the power-
driven door and deliver the corresponding instructions to
the system user.
Only use original spare parts for any repairs or for replacing
parts.
The guarantee is void if this product is used in
combination with others of other brands.
The manufacturer of the drive declines any responsibility if
components incompatible with safety and correct operation
are installed.
- 18 -