Explanation Of General View - Makita LS1216 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Stopper pin
2 Hex bolt(s)
3 Blade guard
4 Kerf board
5 Saw blade
6 Blade teeth
7 Left bevel cut
8 Straight cut
9 Right bevel cut
10 Lock lever
11 Locking screw
12 Adjusting bolt
13 Turn base
14 Stopper lever
15 Slide pipe
16 Top surface of turn base
17 Periphery of blade
18 Guide fence
19 Stopper arm
20 Adjusting screw
21 Grip
22 Cam
23 Levers
24 Latch lever
25 Scale plate
26 Release button
27 Pointer
28 Lock-off button
29 Switch trigger
30 Hole for padlock
31 Switch for light
32 Light
33 Switch for laser
34 Wrench holder
35 Hex wrench
36 Center cover
SPECIFICATIONS
Model
Blade diameter .................................................................................................................................................... 305 mm
Blade body thickness ........................................................................................................................... 1.6 mm – 2.4 mm
Hole diameter.....................................................European countries: 30 mm, other than European countries: 25.4 mm
Max. Miter angle.................................................................................................................................. Left 52°, Right 60°
Max. Bevel angle..................................................................................................................................Left and Right 45°
Max. cutting capacities (H x W)
Miter angle
Thickness of wood
0°
facing on guide
fence for increased
height of cut
45° (left and
Thickness of wood
right)
facing on guide
fence for increased
height of cut
16

Explanation of general view

37 Hex socket bolt
38 Blade case
39 Shaft lock
40 Arrow
41 Inner flange
42 Outer flange
43 Ring
44 Dust nozzle
45 Socket wrench
46 Fastener
47 Spindle
48 Cover
49 Button
50 Dust box
51 Cylinder section
52 Sawdust
53 Support
54 Turn base
55 Clamping screws
56 Upper fence
57 Lower fence
58 Red indicating area
59 Vise knob
60 Vise arm
61 Vise rod
62 Screw
63 Vise plate
64 Vise nut
65 Holder
66 52/38° type crown molding
67 45° type crown molding
68 45° type cove molding
69 Inside corner
70 Outside corner
71 Crown molding stopper L
(Optional accessory)
45° (left)
59 mm × 382 mm
69 mm × 363 mm
35 mm 78 mm × 290 mm
60 mm –
59 mm × 268 mm
69 mm × 255 mm
30 mm –
45 mm –
72 Crown molding stopper R
(Optional accessory)
73 Crown molding stopper L
74 Crown molding stopper R
75 Crown molding
76 Vise
77 Spacer block
78 Aluminum extrusion
79 Over 15 mm
80 Over 290 mm
81 Over 340 mm
82 Hole
83 Cut grooves with blade
84 Screws (two each side)
85 Lower fence
86 Base
87 Platform
88 Vertical vise
89 Workpiece
90 Triangular rule
91 Miter scale
92 Bevel scale plate
93 0° Angle adjusting bolt
94 Top surface of turn table
95 Left 45° bevel angle adjusting
bolt
96 Right 45° bevel angle adjusting
bolt
97 Laser line
98 Screwdriver
99 Screw (one piece only)
100 Lens for the laser light
101 Limit mark
102 Brush holder cap
103 Dust bag
LS1216/LS1216L/LS1216F/LS1216FL
Bevel angle
0°
87 mm × 382 mm 44 mm × 382 mm
102 mm × 363 mm 54 mm × 363 mm
115 mm × 300 mm 61 mm × 290 mm
120 mm × 250 mm
87 mm × 268 mm 44 mm × 268 mm
102 mm × 255 mm 54 mm × 255 mm
115 mm × 202 mm
120 mm × 172 mm
45° (right)
–
–
–