Compound Cutting - Makita LS1219 Manual De Instrucciones

8.
When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.

Compound cutting

Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and Right 0° - 45°
When performing compound cutting, refer to "Press cut-
ting", "Slide (push) cutting", "Miter cutting" and "Bevel
cut" explanations
Cutting base boards
CAUTION:
Make sure to use the horizontal
YLVH RSWLRQDO DFFHVVRU\ ZKHQ FXWWLQJ WKH EDVH
board.
CAUTION:
When cutting the workpiece of the
WKLFNQHVV  PP RU WKLQQHU PDNH VXUH WR XVH D
spacer block to secure the workpiece.
When cutting the base board in 45° miter angle, engage
the stopper lever to prevent the blade case from con-
tacting the base board. This will keep the clearance
between the base board and the blade case when the
carriage is fully pushed forward.
5HIHU WR WKH 63(&,),&$7,216 IRU EDVH ERDUG FXWWLQJ
capacity.
Fig.46: 1. Stopper lever 2. Spacer block
3. Horizontal vise
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
PLWHU VDZ ZLWK WKH PROGLQJV ODLG ÀDW RQ WKH WXUQ EDVH
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
Fig.47: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
7KHUH DUH FURZQ DQG FRYH PROGLQJ MRLQWV ZKLFK DUH
PDGH WR ¿W ,QVLGH ƒ FRUQHUV D DQG E LQ WKH ¿JXUH
DQG 2XWVLGH ƒ FRUQHUV F DQG G LQ WKH ¿JXUH
(a) (b)
1
1. Inside corner 2. Outside corner
Bevel angle
Left and Right 0° - 45°
(c) (d)
2
25 ENGLISH
1
(b)
(a)
(b)
(a)
1. Inside corner 2. Outside corner
Measuring
0HDVXUH WKH ZDOO ZLGWK DQG DGMXVW WKH ZLGWK RI WKH
ZRUNSLHFH DFFRUGLQJ WR LW $OZD\V PDNH VXUH WKDW ZLGWK
of the workpiece's wall contact edge is the same as wall
length.
Fig.48: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
$OZD\V XVH VHYHUDO SLHFHV IRU WHVW FXWV WR FKHFN WKH
saw angles.
When cutting crown and cove moldings, set the bevel
DQJOH DQG PLWHU DQJOH DV LQGLFDWHG LQ WKH WDEOH $ DQG
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
(a) (b)
1
1. Inside corner 2. Outside corner
Table (A)
– Molding Bevel angle
position
52/38°
in the
W\SH
¿JXUH
For (a) Left
inside 33.9°
corner
(b)
For (c)
outside
(d)
corner
(a)
(b)
(a)
(b)
(d)
2
(c)
(a)
(b)
(c) (d)
2
Miter angle
ƒ W\SH 52/38° ƒ W\SH
W\SH
Left 30° Right Right
31.6° 35.3°
Left Left
31.6° 35.3°
Right Right
31.6° 35.3°