Adjusting The Cutting Angle - Makita LS1219 Manual De Instrucciones

NOTICE:
1HYHU XVH JDVROLQH EHQ]LQH WKLQQHU
DOFRKRO RU WKH OLNH 'LVFRORUDWLRQ GHIRUPDWLRQ RU
FUDFNV PD\ UHVXOW

Adjusting the cutting angle

7KLV WRRO LV FDUHIXOO\ DGMXVWHG DQG DOLJQHG DW WKH IDFWRU\
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
Lower the handle fully and lock it in the lowered position
by the stopper pin. Push the carriage toward the guide
fence. Loosen the grip and the screws which secure the
pointer and miter angle scale.
Fig.59: 1. Screw on pointer 2. Screws on miter
angle scale 3. Miter scale
Set the turn base to the 0° position using the positive
stop function. Square the side of the blade with the face
of the guide fence using a triangular rule or try-square.
While keeping the square, tighten the screws on the
PLWHU DQJOH VFDOH $IWHU WKDW DOLJQ WKH SRLQWHUV ERWK
right and left) with the 0° position in the miter angle
scale and then tighten the screw on the pointer.
Fig.60: 1. Triangular rule
Bevel angle
0° bevel angle
Push the carriage toward the guide fence and lock the
sliding movement by the stopper pin. Lower the handle
fully and lock it in the lowered position by the stopper
SLQ DQG WKHQ ORRVHQ WKH NQRE 7XUQ WKH ƒ DGMXVWLQJ
bolt two or three revolutions counterclockwise to tilt the
blade to the right.
Fig.61: 1. ƒ $GMXVWLQJ EROW 2. Screw
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
VTXDUH HWF E\ WXUQLQJ WKH ƒ DGMXVWLQJ EROW FORFNZLVH
7KHQ WLJKWHQ WKH NQRE ¿UPO\ WR VHFXUH WKH ƒ DQJOH \RX
have set.
Fig.62: 1. Triangular rule 2. Saw blade 3. Top sur-
face of turn base
Check if the side of the blade squares with the turn base
surface once again. Loosen the screw on the pointer.
$OLJQ WKH SRLQWHU ZLWK ƒ SRVLWLRQ LQ WKH EHYHO DQJOH
scale and then tighten the screw.
45° bevel angle
NOTICE:
%HIRUH DGMXVWLQJ WKH ƒ EHYHO DQJOH
¿QLVK ƒ EHYHO DQJOH DGMXVWPHQW
Loosen the knob and fully tilt the carriage to the side
that you want to check. Check if the pointer indicates
the 45° position in the bevel angle scale.
Fig.63
If the pointer does not indicate the 45° position, align
LW ZLWK ƒ SRVLWLRQ E\ WXUQLQJ WKH DGMXVWLQJ EROW RQ WKH
opposite side of the bevel angle scale.
Fig.64: 1. /HIW ƒ DGMXVWLQJ EROW 2. 5LJKW ƒ DGMXVW-
ing bolt
Adjusting the laser line position
For model LS1219L only
WARNING:
adjusting the laser line. Take extra care not to
switch on the tool during adjustment. $FFLGHQWDO
start up of the tool may result in serious personal
LQMXU\
CAUTION:
1HYHU ORRN GLUHFWO\ LQWR WKH ODVHU
beam. Direct eye exposure to the beam could cause
serious damage to your eyes.
NOTICE:
Check the position of laser line regu-
ODUO\ IRU DFFXUDF\
NOTICE:
Beware that impacts to the tool. It may
cause the laser line to be misaligned or may cause
damage to the laser, shortening its life.
NOTICE:
+DYH WKH WRRO UHSDLUHG E\ D 0DNLWD
DXWKRUL]HG VHUYLFH FHQWHU IRU DQ\ IDLOXUH RQ WKH
laser unit.
The movable range of laser line is decided by the range
DGMXVWPHQW VFUHZV RQ ERWK VLGHV 3HUIRUP IROORZLQJ
procedures to alter the laser line position.
1.
Unplug the tool.
2. Draw a cutting line on the workpiece and place it
RQ WKH WXUQ EDVH $W WKLV WLPH GR QRW VHFXUH WKH ZRUN-
piece with a vise or similar securing device.
3. Lower the handle and align the cutting line with
the saw blade.
4.
Return the handle to the original position and
secure the workpiece with the vertical vise so that the
workpiece does not move from the position you have
determined.
5. Plug in the tool and turn on the laser switch.
6.
/RRVHQ WKH DGMXVWLQJ VFUHZ 7R PRYH WKH ODVHU OLQH
DZD\ IURP WKH EODGH WXUQ WKH UDQJH DGMXVWPHQW VFUHZV
counterclockwise. To move the laser line close to the
EODGH WXUQ WKH UDQJH DGMXVWPHQW VFUHZ FORFNZLVH
Adjusting the laser line on the left side of the blade
Fig.65: 1. $GMXVWLQJ VFUHZ 2. 5DQJH DGMXVWPHQW
screw 3. Hex wrench 4. Laser line 5. Saw
blade
Adjusting the laser line on the right side of the
blade
Fig.66: 1. $GMXVWLQJ VFUHZ 2. 5DQJH DGMXVWPHQW
screw 3. Hex wrench 4. Laser line 5. Saw
blade
7. 6OLGH WKH DGMXVWLQJ VFUHZ WR WKH SRVLWLRQ WKDW WKH
laser line comes onto the cutting line and then tighten.
NOTE: The movable range of laser line is factory
DGMXVWHG ZLWKLQ  PP IURP WKH VLGH VXUIDFH RI EODGH
29 ENGLISH
The tool must be plugged in while