Makita LS1219 Manual De Instrucciones página 28

Special Max Width Cutting
Capacities Technique
The maximum width cutting capacity of this tool can be
achieved by following the steps below:
For the maximum cutting width of this tool refer to the
63(&,),&$7,216 XQGHU &XWWLQJ FDSDFLWLHV IRU VSHFLDO
cuttings".
1. Set the tool at 0° or 45° miter angle and make sure
that the turn base is locked. (Refer to the section titled
$GMXVWLQJ WKH PLWHU DQJOH 
2. Remove both right and left upper fences temporar-
ily and set aside.
3.
Cut a platform to the dimensions indicated in the
¿JXUH XVLQJ D  PP WKLFN ÀDW VWRFN PDWHULDO VXFK DV
wood, plywood or particle board.
Fig.55: 1. 0° Miter angle: Over 450 mm 2. 45° Miter
angle: Over 325 mm 3. 38 mm 4. Over
760 mm
WARNING:
%H VXUH WR XVH ÀDW VWRFN DV D
platform. 6WRFN WKDW LV QRW ÀDW PD\ PRYH GXULQJ WKH
cutting operation which may result in kickback and
VHULRXV SHUVRQDO LQMXU\
NOTE: The maximum cutting capacity in height will
be reduced by the same amount as the platform
thickness.
4. Place the platform on the tool so that it extends
equally over each side of the tool base.
Secure the platform to the tool using four 6 mm wood
screws through four holes in the lower fences.
Fig.56: 1. Screws (two each side) 2. Lower fence
3. Base 4. Platform
WARNING:
0DNH VXUH WKDW WKH SODWIRUP LV OD\-
LQJ ÀDW DJDLQVW WKH WRRO EDVH DQG VHFXUHG ¿UPO\
to the lower fences using the four screw holes
provided. Failure to properly secure the platform may
result in movement and possible kickback resulting in
VHULRXV SHUVRQDO LQMXU\
WARNING:
(QVXUH WKDW WKH WRRO LV ¿UPO\
PRXQWHG WR D VWDEOH DQG ÀDW VXUIDFH Failure to
properly mount and secure the tool could cause the
tool to be unstable resulting in a loss of control and/
or the tool falling which may result in serious personal
LQMXU\
5.
Install the upper fences on the tool.
WARNING:
Do not use the tool without upper
fences installed. The upper fences provide the ade-
quate support required to cut the workpiece.
If the workpiece is not supported properly, it may
move resulting in possible loss of control, kickback
DQG VHULRXV SHUVRQDO LQMXU\
6.
Place the workpiece to be cut on the platform
secured to the tool.
7. 6HFXUH WKH ZRUNSLHFH ¿UPO\ DJDLQVW WKH XSSHU
fences with a vise before cutting.
Fig.57: 1. Upper fence 2. Vertical vise 3. Workpiece
4. Platform
8.
Make a cut through the workpiece slowly accord-
ing to the operation titled "Slide (push) cutting (cutting
wide workpieces)."
WARNING:
VHFXUHG ZLWK WKH YLVH DQG PDNH WKH FXW VORZO\
Failure to do so may cause the workpiece to move
resulting in possible kickback and serious personal
LQMXU\
WARNING:
become weakened after several cuts are per-
formed at various miter angles. If the platform
becomes weakened due to the multiple kerf cuts left
in the material, the platform should be replaced. If the
weakened platform is not replaced, it may cause the
workpiece to move, during cutting, resulting in possi-
EOH NLFNEDFN DQG VHULRXV SHUVRQDO LQMXU\
&DUU\LQJ WRRO
Before carrying, make sure to unplug and all movable
SDUWV RI WKH PLWHU VDZ DUH VHFXUHG $OZD\V FKHFN WKH
following:
‡ 7KH WRRO LV XQSOXJJHG
‡ 7KH FDUULDJH LV DW ƒ EHYHO DQJOH SRVLWLRQ DQG
secured.
‡ 7KH FDUULDJH LV ORZHUHG DQG ORFNHG
‡ 7KH FDUULDJH LV IXOO\ VOLG WR WKH JXLGH IHQFH DQG
locked.
‡ 7KH WXUQ EDVH LV DW WKH IXOO ULJKW PLWHU DQJOH SRVL-
tion and secured.
‡ 7KH KROGHUV DUH VWRUHG DQG VHFXUHG
Carry the tool by holding both sides of the tool base as
VKRZQ LQ WKH ¿JXUH
Fig.58
WARNING:
LV IRU FDUU\LQJ DQG VWRUDJH SXUSRVHV RQO\ DQG QRW
IRU DQ\ FXWWLQJ RSHUDWLRQV The use of the stopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
VHULRXV SHUVRQDO LQMXU\
CAUTION:
$OZD\V VHFXUH DOO PRYLQJ SRUWLRQV
EHIRUH FDUU\LQJ WKH WRRO If portions of the tool move
or slide while being carried, loss of control or balance
PD\ RFFXU DQG UHVXOW LQ SHUVRQDO LQMXU\
MAINTENANCE
WARNING:
switched off and unplugged before attempting
to perform inspection or maintenance. Failure to
unplug and switch off the tool may result in accidental
start up of the tool which may result in serious per-
VRQDO LQMXU\
WARNING:
sharp and clean for the best and safest perfor-
mance. $WWHPSWLQJ D FXW ZLWK D GXOO DQG RU GLUW\ EODGH
may cause kickback and result in a serious personal
LQMXU\
28 ENGLISH
Ensure that the workpiece is
%H DZDUH WKDW WKH SODWIRUP PD\
Stopper pin for carriage elevation
$OZD\V EH VXUH WKDW WKH WRRO LV
$OZD\V EH VXUH WKDW WKH EODGH LV