Makita LS1219 Manual De Instrucciones página 27

Sierra de inglete telescópica
Ocultar thumbs Ver también para LS1219:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 105
(a) (b)
1
1. Inside corner 2. Outside corner
Table (C)
Molding
position in
WKH ¿JXUH
For inside
(a)
corner
(b)
For outside
(c)
corner
(d)
Cutting aluminum extrusion
Fig.52: 1. Vise 2. Spacer block 3. Guide fence
4. $OXPLQXP H[WUXVLRQ 5. Spacer block
When securing aluminum extrusions, use spacer blocks
RU SLHFHV RI VFUDS DV VKRZQ LQ WKH ¿JXUH WR SUHYHQW
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the blade.
WARNING:
Never attempt to cut thick or
round aluminum extrusions. Thick or round alumi-
QXP H[WUXVLRQV FDQ EH GLI¿FXOW WR VHFXUH DQG WKH ZRUN
may loosen during the cutting operation which may
UHVXOW LQ ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
Wood facing
WARNING:
Use screws to attach the wood
facing to the guide fence. The screws should be
installed so that the screw heads are below the
VXUIDFH RI WKH ZRRG IDFLQJ VR WKDW WKH\ ZLOO QRW
interfere with the positioning of the material being
cut. Misalignment of the material being cut can case
unexpected movement during the cutting operation
which may result in a loss of control and serious
SHUVRQDO LQMXU\
(c) (d)
2
Miter angle
Finished
piece
Right 45°
Save the right
side of blade
Left 45°
Save the left
side of blade
Save the right
side of blade
Right 45°
Save the left
side of blade
CAUTION:
Use straight wood of even thick-
ness for the wood facing.
CAUTION:
,Q RUGHU WR FRPSOHWHO\ FXW WKURXJK
workpieces with a height of 107 mm to 120 PP D
wood facing should be used on the guide fence.
The wood facing will space the workpiece away from
the fence allowing the blade to complete a deeper
cut.
NOTICE:
:KHQ WKH ZRRG IDFLQJ LV DWWDFKHG GR
not turn the turn base with the handle lowered.
The blade and/or the wood facing will be damaged.
Use of wood facing helps to assure splinter-free cuts
LQ ZRUNSLHFHV $WWDFK D ZRRG IDFLQJ WR WKH JXLGH IHQFH
using the holes in the guide fence and 6 mm screws.
6HH WKH ¿JXUH FRQFHUQLQJ WKH GLPHQVLRQV IRU D VXJ-
gested wood facing.
Fig.53: 1. Hole 2. Over 15 mm 3. Over 270 mm
4. 90 mm 5. 145 mm 6. 19 mm 7. 115 -
120 mm
EXAMPLE When cutting workpieces 115 mm and
120 mm high, use a wood facing with the following
thickness.
Miter angle
Left and Right 45°
Left and Right 60°
Groove cutting
WARNING:
W\SH RI FXW E\ XVLQJ D ZLGHU W\SH EODGH RU GDGR
blade. $WWHPSWLQJ WR PDNH D JURRYH FXW ZLWK D ZLGHU
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
SHUVRQDO LQMXU\
WARNING:
to the original position when performing other
than groove cutting. $WWHPSWLQJ WR PDNH FXWV ZLWK
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
For a dado type cut, perform as follows:
1.
$GMXVW WKH ORZHU OLPLW SRVLWLRQ RI WKH EODGH XVLQJ
WKH DGMXVWLQJ VFUHZ DQG WKH VWRSSHU DUP WR OLPLW WKH FXW-
ting depth of the blade. Refer to "Stopper arm" section
described on previously.
2.
$IWHU DGMXVWLQJ WKH ORZHU OLPLW SRVLWLRQ RI WKH EODGH
cut parallel grooves across the width of the workpiece
using a slide (push) cut.
Fig.54: 1. Cut grooves with blade
3.
Remove the workpiece material between the
grooves with a chisel.
27 ENGLISH
Thickness of wood facing
115 mm
20 mm
15 mm
15 mm
Do not attempt to perform this
Be sure to return the stopper arm
120 mm
38 mm
25 mm
25 mm

Hide quick links:

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ls1219l

Tabla de contenido