Preparation For Use; Donning Procedure - Dräger Oxy 3000 MK II Instrucciones De Uso

2.6 Marking
The following information is shown on the labelling field:
 Date of manufacture
 Serial number
 Order number
 Approval marking
 Testing standard
 Name of device
 Nominal usage period of the device see Section 2.2 on Page 8
3 Use
3.1 Before initial use
Before commissioning, the delivery date must be inscribed on the labelling field.
It is not permitted to use punch numbers for the inscription. Dräger recommends
engraving or etching.
3.2 Using the oxygen self-rescuer
WARNING
!
Keep the oxygen self-rescuer away from combustible substances
(petrol, grease, solvents, etc.) before or during use to prevent a
potential risk of fire!
Destroying the oxygen self-rescuer can result in a potential risk of
ignition if the oxygen-abstracting chemical comes into contact with
combustible substances such as charcoal.
Regularly practise using the oxygen self-rescuer with a training unit

 The oxygen self-rescuer might be difficult to open in cold weather
conditions, and especially at minus temperatures.
 Only open the oxygen self-rescuer when using it!
Otherwise moisture from the ambient air will flow into the open oxygen self-
rescuer and impair its function.
Open devices cannot be closed again. They are considered used and must
not be stored but be disposed of see Section 7 on Page 11.
 Check the oxygen self-rescuer prior to carrying/daily see Section 3.3 on
Page 9.
 Use the oxygen self-rescuer only once.
3.3

Preparation for use

The following work steps must be performed every day. If one of the criteria listed
is not met, the oxygen self-rescuer must not be used.
NOTICE
i
i
If the oxygen self-rescuer suffered unusual strain (blows, pressure,
etc.), the checks mentioned should be carried out immediately.
In the following cases, the oxygen self-rescuer may be repaired by trained
personnel:
 If the oxygen self-rescuer is worn with a shoulder strap or hand strap, check
that they are locked onto the support ring. If the carrying strap is frayed or
damaged, it must be replaced.
 Make sure that the inspection window is not damaged. A damaged
inspection window must be replaced.
In the following cases, the oxygen self-rescuer must be taken out of service or
sent to Dräger for inspection.
 Check that the oxygen self-rescuer is complete.
 Check that the seal is not damaged.
 Check that the casing is closed.
 Check that the opening mechanism is locked and undamaged.
 Check the casing for deformations (see supplementary sheet).
 Ensure that the casing does not have any tears or holes.
 Check inspection window: If many yellow fragments, the same size or larger
than grains of sugar, can be shaken in the inspection window area, the
oxygen self-rescuer must be decommissioned.
An adhesive, thin yellow dust layer is normal after years of carrying and
does not affect the function.
1 not CE-approved.
Dräger Oxy 3000/6000 MK II
 Check if the moisture indicator
(1) is brown. If moisture has
penetrated into the oxygen self-
rescuer, the moisture indicator
changes from
turquoise.
 If the oxygen self-rescuer is used
in accordance with SANS 1737,
make sure that the abrasion
protection is available and not
damaged.
3.4

Donning procedure

NOTICE
i i
Donning the device incorrectly may cause delay when using the
oxygen self-rescuer in emergencies.
Be sure to perform the following steps in the described sequence.
1. Pull the opener up and press it
into its end
tightening straps then release
automatically.
2. Remove and dispose of the
upper part of the casing.
Opening can be supported as
follows:
Use the fully opened opener

1
.
to lever the lid open.
Or
Bend the casing at the face

seal. To do this, place the
device flat on the floor. Push
onto the edge of the upper
and lower parts of the
casing.
In minus

support the opening with
your feet
(analogous to the previous
point).
3. Grasp the yellow loop of the
neck strap and use it to pull the
oxygen self-rescuer out of the
casing.
WARNING
!
Do not pull the oxygen self-rescuer at its mouthpiece, at the hose or at
other parts out of its housing, but only at the yellow loop. Observe the
indicated direction when pulling it out.
Otherwise, the oxygen self-rescuer could be damaged and may not
supply enough breathing air.
4. Throw away the lower part of the housing.
1
brown to
position. The
temperatures,
if necessary
Use
00331209.eps
00931209.eps
01031209.eps
00531209.eps
9