Setting Up A New Model Menu: ( Memo ) New; Entering / Changing The Model Name Menu: ( Memo ) Name; Copying Model Memories Menu: ( Memo ) Copy - Multiplex Cockpit SX Manual De Instrucciones

18.2. Setting up a new model
) NEW
Menu: (
MEMO
Moving to the NEW menu:
to MENU,
to MEMO,
to NEW,
When you set up a new model, the C
offers the last selected model type as the starting point.
Select the desired model type using the 3-D digi-
adjustor: EASY, GLIDER, ACRO, HELI
A brief press on the 3-D digi-adjustor takes you into
the IN MEM menu. Here you select the memory in
which the new model is to be stored.
When you have selected a memory for the new model,
press the 3-D digi-adjustor briefly
NAME menu. (
18.3.)
Notes:
• Only vacant memories are offered
When you leaf through, you will only see the memo-
ries which still contain no data.
• EnterIN MEM = 0 for no new model
If you select 0 using the 3-D digi-adjustor, and con-
firm your choice with a brief press on the 3-D digi-
adjustor , a new model is not set up, and you are re-
turned to the NAME menu.
• Conclude with a long press
This is an alternative method of concluding the pro-
cess without setting up a new model (wait for the
confirmation beep). In this case you are returned to
the INFO 1 display.
The method of setting up the individual model types is
described in the following sections:
13.3.1. for EASY
15.3.1. for ACRO
18.3. Entering / changing the model name
) NAME
Menu: (
MEMO
The method of entering the model name is described in
detail in the sections covering each model type.
The procedure for changing the model name:
to MENU,
to MEMO,
to NAME,
(current name appears, first character flashes)
Enter the desired characters one by one:
select number, symbol or letter
(0 to 9, :, /, <, -, >, ?, space, A to Z)
proceed to next character
interrupt data entry process, go to INFO 1
After the sixth character a brief press
the NAME menu.
(SETUP appears),
(GO TO appears),
(model type flashes)
SX always
OCKPIT
to move into the
14.3.1. for GLIDER
16.3.1. for HELI
(SETUP appears),
(GO TO appears),
returns you to
Operating Instructions
18.4. Copying model memories
Menu: (
There are two reasons for copying model memories:
1. You may wish to set up a new model, and already
have a similar model stored in another memory.
2. You may wish to try out different settings on a model
without changing the settings in the existing memory.
When you copy a memory, the current model memory
is always used as the source; it is copied into the se-
lected destination memory.
Moving to the KOPIE menu:
to MENU,
to MEMO,
to COPY,
Current memory
Select the destination for the copy using the 3-D digi-
adjustor. A brief press
out the copy process, then returns you to the KOPIE
menu.
Notes:
• Only vacant memories are offered
When you are selecting a memory, you will only see
the memories which still contain no data.
• If all model memories contain model data, you
will be unable to select a destination memory.
In this case the flashing 0 cannot be changed using
the 3-D digi-adjustor.
• Select COPY = 0 if you do not wish to copy
If you select 0 with the 3-D digi-adjustor and confirm
your choice with a brief press , a new model will not
be set up, and you will be returned to the COPY
menu.
• Concluding with a long press
This is an alternative method of concluding the pro-
cess without setting up a new model (wait for the
confirmation beep). In this case you are returned to
the INFO 1 display.
Important: no automatic switch to the copy
When the copy process is complete, you remain in the
current memory. If you wish to make changes to the
copy, you must select the copy in the GO TO menu.
Page 75
) COPY
MEMO
(SETUP appears),
(GO TO appears),
(0 flashes)
Destination for copy
on the 3-D digi-adjustor carries