Brill Brillencio 43 BR comfort Manual Del Usuario página 24

you restart the motor and begin
mowing again. Inspect your lawn-
mower immediately if it begins to
GB
vibrate unusually vigorously.
Note:
When working on slopes and
inclines always work diagonally to
the incline. You can prevent the
lawnmower from sliding downhill
by mowing slightly diagonally
upwards. Do not mow extremely
steep slopes and take extra care
when changing directions on
slopes.
Clean the underside of the mower
housing on a regular basis. Remove
grass residues, which make it more
difficult to start the motor and
impair the cutting quality and
ejection of grass cuttings.
Always switch off the motor before
leaving your lawnmower unattend-
ed and before pouring petrol into
the fuel tank.
8.3. Mowing with the Grass Catcher
Figure H
The grass catcher must be
emptied as soon as grass cuttings
9. Maintenance, Care and Storage
9.1. Maintenance
Maintenance covers all work that
keeps your lawnmower in good
working order. You can prevent
accidents and failure of parts by
checking your lawnmower regularly
(check that the bolted connections
are secure, check for cracks
and damage) and by replacing
damaged or worn parts.
Repairs must only be carried out
by the service centres authorised by
the manufacturer or authorised
specialist dealers. A service centre
directory is supplied with your
lawnmower.
Warning! Always unplug
A
the spark plug connector
before carrying out all work and
repairs on your lawnmower.
Otherwise there is a risk of injury.
24
are left on the lawn while
mowing.
Warning! Always switch off
A
the motor and wait for the
cutting tool to stop rotating before
removing the grass catcher.
To remove the grass catcher, move
the safety handle forwards over
the stop (Figure H) Pos. 0, which
releases the folding handle.
Push the handle forwards to open
the multi-function box. Hold the
grass catcher by the handle with
one hand and remove (Figure J
Pos. 11).
Note:
To ensure the grass catcher is filled
as full as possible, you should clean
the grass catcher and above all the
air grille after each use.
Warning! Do not use your
A
hands or feet to remove
grass cuttings from the mower
housing. Use a suitable implement
such as a broom or dustpan brush.
To empty the grass catcher once
removed, hold it by the handle with
one hand and with the other hand
Check the grass catching device
regularly for wear or reduced
function. Replace defective
silencers. For safety reasons,
always replace worn or damaged
parts.
Never clean your lawnmower
under running water and in
particular never using a high-
pressure water jet due to the
danger of injury to people and
property.
Store your lawnmower in a dry
place that is protected from frost.
Store your lawnmower out of the
reach of children.
Do not tip the motor onto the spark
plug side/carburettor side.
Observe the notes on installation
for exchanging the blade.
in the rear recess, tip the grass
cuttings out of the large opening
at the front.
Figure K
After emptying the grass catcher
fit it back into the holders
provided and tilt back the multi-
function box.
Warning! The cutting tool
A
does not start rotating while
the multi-function box is open.
Move the handle back to the work-
ing position and ensure it snaps
into place. Take care not to trap the
Bowden cables.
Warning! Only attach
A
the grass catcher when the
motor is switched off and the
cutting tool has stopped rotating.
Mowing without the Grass Catcher
The Brill brillencio lawnmower is
ideal for mowing long grass.
If you mow your lawn without the
grass catcher the grass cuttings
are distributed evenly over the lawn
from the high rear grass ejection
chute.
Maintenance on Wheel Drive
Figure M Pos. 1
The gears run without maintenance
in a sealed oil bath. The wheel
drive clutch cable can be readjust-
ed if the clutch is acting too late or
is slipping. To adjust the cable, turn
the actuating wheel clockwise from
the operator's side. To ease it, turn
the actuating wheel anti-clockwise
from the operator's side.
9.2. Exchanging the Blade
Please only use original replace-
ments blades supplied by the
manufacturer. Original replacement
blades are available from your
specialist dealer.