Service And Repair - Vollrath SLM300/S Manual Del Operador

MAINTENANCE (CONTINUED)
9. Simultaneously press and hold the sharpening and deburring stone
buttons for 3-4 seconds. Release the buttons.
NOTICE: NOTICE: Pressing the buttons for longer than 3-4 seconds
could bend the blade, which could then damage the
slicer.
10.Press and release the OFF (O) button and unplug the slicer.
11.Return the sharpener to the original position.
12.Clean the slicer. See "Clean and Sanitize the Slicer" on page 5.
Lubricate the Carriage Slide
Lubricate the carriage slide at least once a month and any time that
pushing the tray becomes difficult.
NOTICE: NOTICE: Use the oil supplied with the slicer or a food safe
lubricant. Do NOT use vegetable oil or oil containing
silicone. Do NOT spray oil onto the slicer components.
Sprayed oil could unintentionally reach areas of the slicer
that should not be lubricated.
TROUBLESHOOTING
Problem
Poor cutting performance.
Poor cutting performance even though
blade is routinely sharpened.
No sparks when sharpening.
Dirty sharpening stones.
Overload reset is activating too often.
Gauge plate is difficult to adjust

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or
replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services
for instructions.
When contacting Vollrath Technical Services, please be ready with the
item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
www.vollrath.com
Might Be Caused By
The blade needs to be sharpened.
Sharpening process is incorrect.
Sharpening stones need to be replaced.
Blade was not cleaned prior to sharpening. Replace the stones.
Gauge plate slide needs lubrication.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
1. Press and release the OFF (O) button.
2. Unplug the slicer from the electrical outlet.
3. Use a clean soft cloth to clean the carriage slide.
4. Pull carriage all the way forward. This will align the carriage slide
with the oil access hole (OIL) on the front of the slicer. If the slide is
not aligned, oil will drip and pool below the slicer.
5. Put a few drops of the oil that was supplied with slicer into the
carriage slide lubricant access hole.
Course of Action
Sharpen the blade.
Repeat the sharpening process. Press and hold the sharpen-
ing stone button for a few seconds longer to allow burrs to
form on the blade. If the problem persists contact Vollrath
Technical Services.
Replace the stones.
Contact Vollrath Technical Services.
Lubricate the gauge plate slide with the oil supplied with the
slicer or with a food-grade lubricant.See page 6.
WARRANTY STATEMENT FOR THE VOLLRATH CO.
The Vollrath Company LLC warrants the products it manufactures or
distributes against defects in materials and workmanship as specifically
described in our full warranty statement.
For complete warranty information, product registration and new
product announcement, visit www.vollrath.com.
Technical Services
techservicereps@vollrathco.com
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
©
2017 The Vollrath Company L.L.C. Part No. 350009-1 ml 6/16/17