Moretti Forni P Classic Serie Manual De Instrucciones página 22

- Replace the thermostat (item 33 plate C) (item 32 plate A Amalfi)
and the respective sensor, along with any worn rock wool insulation,
if necessary;
- Perform the above operations in reverse order to reassemble.
5.3.10 HEATING ELEMENT REPLACEMENT
(P60E-P80E-P120E)
After carrying out the operations in point 5.1, to replace the elements,
proceed as follows:
- remove the right side panel (item 29 tab.A- tab.B) (item 22 tab.C)
loosen the four fastening screws;
- disconnect the power cables from the element to be replaced;
- use a blade to remove the rock wool section concerned;
- loosen the two fastening screws;
- replace the heating element;
- carry out the above steps in reverse order to refit the parts, replacing
the rock wool section previously removed, if necessary.
5.4 REPLACING PARTS
COMPARTMENT
5.4.1 REPLACING THE LIGHT BULB
After carrying out the operations described in 5.1 above, to replace the
light bulb and/or cover, proceed as follows from the inside of the
leavening compartment:
- Unscrew the cover (fig.20 item A) and replace the bulb (fig.20 item
B) and/or the cover itself.
- Replace the cover.
5.4.2 REPLACING THE DOOR KNOB
After carrying out the operations described in 5.1 above, to replace the
door knob proceed as follows:
- Open the doors of the leavening compartment (plate D);
- Remove the plug (plate D).
- Unscrew the fixing nut inside the ball knob (plate D).
- Replace the ball knob (item 2 plate D) and fasten the fixing.
5.4.3 REPLACING THE THERMOSTAT
After carrying out the operations described in 5.1 above, to replace the
thermostat proceed as follows:
- Remove the control panel fixing screws (plate D);
- Disconnect the thermostat faston connectors;
- Remove the thermostat dial (item 5 plate D);
- Unscrew the thermostat lock nut (item 6 plate D);
- Remove the thermostat sensor located inside the compartment;
- Replace the thermostat (item 7 plate D) and the respective sensor.
- Perform the above operations in reverse order to reassemble.
5.4.4 REPLACING THE MAGNETIC DOOR FASTENER
After carrying out the operations described in 5.1 above, to replace the
magnetic door fastener proceed as follows:
- Open the doors of the leavening compartment (plate D).
- Remove the seal snap ring (plate D).
- Replace the magnetic door fastener (item 15 plate D).
5.4.5 REPLACING THE THERMOSTAT DIAL AND RING
NUT
After carrying out the operations described in 5.1 above, to replace the
thermostat dial and/or relative ring nut, proceed as follows from the
outside of the compartment:
- Remove the snap-on thermostat dial (item 5 plate D).
- Unfasten the lock nut (item 6 plate D).
- Replace the lock nut and/or the dial.
5.4.6 REPLACING THE INDICATOR LIGHT AND THE
LIGHT SWITCH
After carrying out the operations described in 5.1 above, to replace the
indicator light and the light switch proceed as follows:
- Remove the control panel fixing screws (plate D).
- Disconnect the faston connectors for the indicator and/or the light
switch.
- Replace the indicator light (item 14 plate D).
- Replace the push button (item 4 plate D).
- Perform the above operations in reverse order to reassemble.
5.4.7 REPLACING THE HEATING ELEMENTS
After carrying out the operations described in 5.1 above, to replace the
heating elements proceed as follows:
- Unfasten the panel fixing screws (plate D);
- Disconnect the heating element supply wires;
- Remove the heating elements (item 10 plate D);
OF THE LEAVENING
- Perform the above operations in reverse order to reassemble.
5.5 REPLACING
COMPARTMENT WITH HUMIDIFIER
5.5.1 REPLACING THE TRAY HEATING ELEMENT
After carrying out the operations described in 5.1 above, to replace the
tray heating element proceed as follows:
- Unfasten the fixing screws (plate D);
- Disconnect the heating element supply wires (item 19 plate D);
- Remove the heating element (item 19 plate D).
- Perform the above operations in reverse order to reassemble:
5.5.2 REPLACING THE INDICATOR LIGHT AND THE
HUMIDIFIER SWITCH
After carrying out the operations described in 5.1 above, to replace the
indicator light and the humidifier switch proceed as follows:
- Remove the control panel fixing screws (plate D).
- Disconnect the faston connectors for the indicator and/or the
humidifier switch.
- Replace the indicator light (item 3 plate D).
- Replace the humidifier switch (item 13 plate D).
- Perform the above operations in reverse order to reassemble.
5.6 DISPOSAL
When the oven or its spare parts are dismantled, the various
components must be sorted by type of material and disposed of in
compliance with current local laws and regulations.
The presence of a wheeled dustbin with a line
through it indicates that within the European Union
electrical components are subject to special collection
at the end of their working life. As well as to this
device, the standard applies to all of its accessories if
marked with this symbol. Do not dispose of this
product as normal urban waste.
6 LIST OF SPARE PARTS
Index of plates
Plate A Baking chamber assembly P60E-P80E
Plate B Baking chamber assembly Amalfi
Plate C Baking chamber assembly P120E
Plate D Leavening compartment assembly
Plate E Steamer assembly
Plate F Wiring diagram P60E-P80E
Plate G Wiring diagram Amalfi A-B-C
Plate H Wiring diagram Amalfi D
Plate I Wiring diagram P120E A-B
Plate L Wiring diagram P120E C
Plate M Wiring diagram leavening compartment
Plate N Electric diagram vapour aspiration hood.
INSTRUCTIONS FOR ORDERING SPARE PARTS
Orders for spare parts must contain the following information:
- Appliance type
- Appliance serial number
- Name of part
- Number required
UK/9
PARTS OF THE LEAVENING