Publicidad
6
INSTALACIÓN ELÉCTRICA
Wire "Sensor 1 and 2" switching inputs of the CLV69x in the CDM420-0006 connection module
a) Sensor supplied by CDM420-0006
e.g. photoelectric sensor
CDM420-0006
U
39 +24 V*
V
X
Name
Out
GND
37 SGND
6 Shield
PNP sensor
S6 : SGND-GND
ON
OFF
CDM420-0006
Terminal X
38
28
Switch S6 : SGND-GND
ON: connect GND of the sensor to the GND of
the CDM420-0006/CLV69x.
OFF: sensors connected volt-free to CDM420-
0006/CLV69x.
Reference potential valid for all "Sensor 1 and 2"
switching inputs and optionally "AUX In 1 and 2"
b) Sensor connected volt-free and externally supplied
e.g. photoelectric
CDM420-0006
U
sensor
V ext
39 +24 V*
U
V
38 Sensor 1
Out
37 SGND
GND
6 Shield
PNP sensor
S6 : SGND-GND
ON
OFF
d) Switch connected volt-free
and externally supplied
Connection of the switch as under b)
Functional assignment for switching inputs via
SOPAS-ET configuration software
Figura 83: Entradas conmutadas "Sensor 1 y 2"
84
I N S T R U C C I O N E S D E S E R V I C I O | CLV69x
1)
Adapter cable
1
2
+24 V*
Y1
Y2
.
.
Shield
.
15
9
S6
5
1
GND
3
10 5
1
6
13
4
5
14
6
15
11
17
7
D-Sub-HD female
M12 male
connector, 15-pin
connector,
17-pin, A-coded
CLV69x
Name
Pin Y2
Sensor Z
Pin Y1
Sensor 1
Sensor 1
14
10
Sensor 2
Sensor 2
15
4
+24 V*
Shield
S6
GND
Characteristic data of the switching inputs "Sensor 1 and 2"
Switching
behavior
Properties
Electrical values
CLV69x
U
2)
V
U
V
Sensor Z
6.64 K
U
e
3.32 K
SensGND
GND
GND
U
= max. 32 V
12
2
11
e
1
16
10
9
15
8
1) Dependent on type
For CLV69x-xxx0 (without heating):
No. 2049764 (0.9 m)
No. 2055419 (2 m)
No. 2055420 (3 m)
No. 2055859 (5 m)
For CLV69x-xxx1 (with heating):
No. 2061480 (2 m)
No. 2061605 (3 m)
No. 2061481 (5 m)
2) Pin 2 in CLV69x-xxx1
(with heating) not
connected
a) Switch supplied by CDM420-0006
CDM420-0006
+24 V*
39 +24 V*
38 Sensor 1
Shield
37 SGND
S6
6 Shield
GND
S6 : SGND-GND
ON
OFF
Current at the input starts the assigned function,
e.g. start reading cycle.
(CLV69x default settings:
logic active high, debouncing 10 mm)
– Opto-decoupled, reverse polarity protected
– Can be wired with PNP output of a sensor
– SensGND is the common insulated
reference potential for all switching inputs
Low:
U
≤ 2 V; I
≤ 0.3 mA
e
e
High:
6 V ≤ U
≤ 32 V;
e
0.7 mA ≤ I
≤ 5 mA
e
8025632/131W/2019-03-06 | SICK
Sujeto a cambio sin previo aviso
Publicidad
Capítulos
